Supplies

Manufactured from type 1 class a Borosilicate glass. Ideal for culture aerobic & anaerobic organisms, media storage and mixing. Deep skirted screw caps protect against contamination. Supplied with rubber line black phenolic caps and graduated to approximate volumes. Size: 25mL Cap: 18-415 Dimensions: 41x65mm (24 per CS )

Manufactured from type 1 class a Borosilicate glass. Ideal for culture aerobic & anaerobic organisms, media storage and mixing. Deep skirted screw caps protect against contamination. Supplied with rubber line black phenolic caps and graduated to approximate volumes. Size: 6L Cap: 38-415 Dimensions: 235x390mm (3 per CS )

The Bellco Sci-ERA Dual Pan Hot Shaker is a slow speed, large orbit shaker with two independently controlled baths for incubation of electrophoretic gels and filter hybridization media. Stringent temperature control with a sensitivity of +/-0.1oC is useful for many biochemical assays. This Bellco design incorporates a seamless stainless steel lined temperature controlled water bath mounted on a low-profile one inch orbiting platform. The unique chamber design offers simple containment of potential spills. The chamber is completely isolated from electromechanical components. The Sci-ERA Dual Pan Hot Shaker has audible over-temperature alarms and built-in safety features to prevent heater burn-out. An easy-to-use microprocessor controller offers stringent temperature control. (1 per EA )

Will not rust or deteriorate in water baths or co2 atmospheres. Manufactured from 303 stainless steel with electropolish finish. Each opening rack 11/16" (17.5mm) Tube size: 16mm Spacing: 10x12 holds 120 tubes Dimensions: 9 1/4" x 7 5/8" x 3" WIRE SPECIFICATIONS: SIDE & UPRIGHTS: .135"OD WIRE, CROSS WIRE: 0.063" OD WIRE, BTTM MESH: 1/4" Minimum order requirement: 5 each (1 per EA )

3/4 ph/do probe holder bioreactor. 316 l stainless steel Ra 32 finish or better (1 per EA )

Disposable gas fermentation tubes are inverted in bottom of larger tube for collection of fermentation gases. Disposible standard flint glass with 1.15mm Wall. 144 per case. Size: 8x29mm (144 per CS )

Glass mc impeller shaft 7mm od x 155mm long Type 1 Class A boro for 100- 250ml spinners Glass Impeller Shaft,100-250mL (1 per EA )

Glass mc impeller shaft 7mm od x 190mm long Type 1 Class A boro for 500ml spinners Glass Impeller Shaft, 500mL (1 per EA )

Type 1 Class A Borosilicate Glass ideal for freeze drying or cryogenic storage. Tubular firing off constriction on the neck. Rigidly controller bottom to withstand pressure at low temperature. Tubular round bottom Length: 170mm Neck od: 8mm Capacity: 4ml (144 per CS )

Approx 25 x 34" (63.5 x 86.5cm). Stainless steel mesh with reinforcing bars. Fits on adjustable clips inside incubator. Load: 240 lbs (max). (1 per EA )

Used to surround a single cell to create homogeneous culture of cells rather than mixed population. The flat end ensures tight sealing with surface of culture dish. Sizes: 8x8mm (125 per CS )

Heavy gauge rectangular construction for easy stacking and storage. These pipette cans can be sterilized by autoclave or dry heat. (do not exceed 400 degrees F). Includes silicone pad on the inside of top and bottom to protect pipette tips. --Satin finish surface of entire can for convenient marking or coding. --Silicone pads on inside of top and bottom protect pipette tips. --Material: 304 stainless steel .031” thick (1 per EA )

Will not rust or deteriorate in water baths or co2 atmospheres. Manufactured from 303 stainless steel with electropolish finish. Each opening rack 1 1/16" (26.9mm) Tube size: 25mm Spacing: 6x8 holds 48 tubes Dimensions: 8 1/4" X 6 3/16"X 3 1/2" WIRE SPECIFICATIONS: SIDE & UPRIGHTS: .135"OD WIRE, CROSS WIRE: 0.063" OD WIRE, BTTM MESH: 1/4" Minimum order requirement: 5 each (1 per EA )

Type 1 class a Borosilicate glass ideal for freeze drying or cryogenic storage. Tubular firing off constriction on the neck. Rigidly controller bottom to withstand pressure at low temperature. Tubular round bottom Length: 145mm Neck od: 8mm Capacity: 3ml (144 per CS )

Manufactured from type 1 class a Borosilicate glass. Includes long skirted black phenolic screw cap with white rubber liner. Screw cap included Size: 20 x 150mm Replacement cap: 2029-00018 (500 per CS )

Description: Bio-Probe Spinner Flask Complete Bio-Probe Spinner Flask Complete consists of: Flask, and Impeller Assembly. Flask Specifications: Material: Type 1 Class A Borosilicate Glass Dimensions: 136mm OD x 240mm Overall Height Two 45mm Side arms angled 60° off center Two 32mm Side arms angled 35° off center One 100mm Screw Thread Center Neck Indented bottom Graduations: 200mL to 1000mL, every 100mL – White Ink (Approx Volumes) Supply with: Two 45mm PP Blue Screw Caps, two PP Blue Pouring Rings, two 32mm blue screw caps, and two o-rings Impeller Assembly Specifications: Impeller Assembly consists of paddle, shaft, O-ring, retaining ring, magnet, magnet holder, adjustable paddle, bearing thimble, bearing spacer, ball bearing, compression spacer, compression washer, sealing ring, cap seal, and screw cap. Adjustable from 220mm-227mm in height. Paddle: PTFE , 4 1/4”x3”x1/16” Shaft: 316L Stainless Steel, 8 7/16” long x ¼” OD O-ring: Silicone, -008 Retaining ring: 316L SST, 0.365” OD x 17/64” ID x 5/32” long Magnet: PTFE coated, ½” OD x 3” long Magnet holder: PTFE, ¾” OD x ¼” ID x 4 11/16” long Adjustable paddle: PTFE, 3 3/8”x 1 ½” with a hub OD of 1 ½” Bearing thimble: PTFE, 1 ¼” OD by 4/4” ID x 3 1/8” long Bearing spacer: PTFE, ¾” OD x ½” ID x 0.880” long Ball bearing: Polybutylene terephthalate & SST, ¾” OD x ¼” ID x 0.281 thick Compression spacer: PTFE, ¾” OD x ½” ID x 1.645” long Compression washer: White Silicone, 1 1/16” OD x ½” ID x 1/16” thick Sealing ring: Red silicone, 3.6” OD x 3” ID x 0.240” thick Cap seal: PTFE, 3 ¾” OD x 0.985” long Screw cap: Blue Polypropylene, 4.25” OD x 7/8” long (1 per EA )

Manufactured from type 1 class a Borosilicate glass. Ideal for all cell culture and media storage purposes. Provides flexible secure seal without a liner. Supplied with gl45 liner-less screw cap and pouring rings. Graduated to approximate volumes. Size: 6L Dimensions: 235x370mm (1 per EA )

3/8" addition port assembly for 3, 7 and 10 liter bioreactor systems/vessels. English threads Fits .375" hole in headplate Dimensions: 2" oal Tube: 1/4" od x 5/32' id Material: SST 316l - ra 32 finish - inside & out With hose barb (1 per EA )

Bellco’s new Low Profile Hot Shaker provides gentle, large orbit shaking motion combined with precise temperature control. Designed to be the perfect solution for incubation of electrophoretic gels and filter hybridization media, the Low Profile layout promotes easy access to the independent microprocessor driven temperature controller and reliable control of shaking speeds up to 75 oscillations per minute. The quiet brushless drive motor and repeatable, stable temperature settings from 5°C above ambient up to 99.9°C may be effectively used in most biochemical, chemical and microbiological applications. (1 per EA )

Blades and impeller assemblies are use for cell culture. Reduces shear in delicate cell culture. Manufactured from 316l stainless steel with electropolish finish. Ra 32 finish or better inside and out. Blade dimension: 5 3/4 x 2". Shaft oal: 17". MARINE IMPELLER INCLUDES 1/2" SHAFT AND IMPELLER BLADE OMNI AND Z-Z PADDLES ARE ONE PIECE WELDED, 1/4" SHAFT (1 per EA )

Ideal for growing, storing and mixing or aerobic and anaerobic cultures. The 3 bottom baffles increase culture oxygenation. Includes 25mm Bellco stainless steel closure (2005 series) Specifications: Type 1 Class A Borosilicate Glass Sizes: 300ml Includes: Bellco Stainless Steel Closure (2005 Series) Sidearm Dimensions: 12x130mm Case Quantity: 4 (4 per CS )

The Bellco Cell Production Roller Apparatus has been designed for production of animal cells, viruses and cell products. Modular units are available from 5 to 45 bottle positions and allow easy expansion with modular add-on decks. Non-modular production units come in 45 and 50 bottle positions with over 80,000 cm2 of surface area. Rollers have a key design to eliminate slipping and are easily removable for servicing of bearings. Rollers are formulated from a chemical-resistant non-slip EDPM. All units feature a solid state control with heavy-duty DC motor and analog tachometer. Non-modular production models feature rubber bumpers, handles and a slotted rear guard. (1 per EA )

Bellco’s new Dual Pan Low Profile Hot Shaker provides gentle, large orbit shaking motion combined with precise temperature control. Designed to be the perfect solution for incubation of electrophoretic gels and filter hybridization media, the Low Profile layout promotes easy access to the independent microprocessor driven temperature controller and reliable control of shaking speeds up to 75 oscillations per minute. The quiet brushless drive motor and repeatable, stable temperature settings from 5°C above ambient up to 99.9°C may be effectively used in most biochemical, chemical and microbiological applications. (1 per EA )

Ideal for florescence and confocal microscopy 520 alphanumeric coded squares .17-.19mm thick Each square measures 0.6mm x 0.6mm #1.5 thickness Facilitates mounting of micro-manipulated cells or chromosome spreads (25 per CS )