Furniture
Selection of furniture needed for scientific, laboratory, research, clean room, and industrial facilities, including benches, cabinets, fume hoods, tables and chairs.
-
7 foot Aluminum Table Top Mount Lab-Frame Kit.
Lee Engineering
$664.43
Special Price $581.38
Lattice frame: Use the open connectors and lattice rods to assemble the frame. The kit assumes a lattice spacing of 1-foot and a border on the sides and top. Spacing may vary depending on your application. Rods may be cut for fit as necessary. Mounting: After assembling the lattice frame attach vertical base plates to the bottom of the vertical rods. There should be an equal number of remaining 2-foot rods, swivel baseplates and open connectors. Connect an open connector to one end of the 2-foot rod and a swivel base plate to the other end. Attach the open connector to the lattice frame 30-45 degrees. Base plates may be secured with #10 screws. Mounting Screws Not Included. NOTE: Follow your fume hood manufacturers’ requirements for attachment Learn More -
6 foot Back Mount Stainless Steel Lab-Frame Kit.
Lee Engineering
$745.00
Special Price $651.88
This mounting option is recommended for situations when you need a lab support lattice to cover the entire back panel of your fume hood. Lattice frame: use the open connectors and lattice rods to assemble the frame. Use one open connector at each rod intersection. The kit assumes a lattice spacing of 1-foot; however, this may vary depending on your application. Rods may be cut for fit as necessary. Mounting: after assembling the lattice frame, there should be an equal number of remaining 4-foot rods, base plates and open connectors. Connect an open connector to one end of the 4-foot rod and a base plate to the other end. Attach the open connector to the lattice frame 90 degrees in a square or rectangular pattern (the base plate pointing to the back mounting surface). Base plates may be secured with #10 screws. Mounting Screws Not Included. Learn More -
7 foot Fiberglass Table Top Mount Lab-Frame Kit.
Lee Engineering
$839.86
Special Price $734.88
Lattice frame: Use the open connectors and lattice rods to assemble the frame. The kit assumes a lattice spacing of 1-foot and a border on the sides and top. Spacing may vary depending on your application. Rods may be cut for fit as necessary. Mounting: After assembling the lattice frame attach vertical base plates to the bottom of the vertical rods. There should be an equal number of remaining 2-foot rods, swivel base plates and open connectors. Connect an open connector to one end of the 2-foot rod and a swivel base plate to the other end. Attach the open connector to the lattice frame 30-45 degrees. Base plates may be secured with #10 screws. Mounting Screws Not Included. NOTE: Follow your fume hood manufacturers’ requirements for attachment. Learn More -
7 foot Back Mount Stainless Steel Lab-Frame Kit.
Lee Engineering
$1,002.29
Special Price $877.00
This mounting option is recommended for situations when you need a lab support lattice to cover the entire back panel of your fume hood. Lattice frame: use the open connectors and lattice rods to assemble the frame. Use one open connector at each rod intersection. The kit assumes a lattice spacing of 1-foot; however, this may vary depending on your application. Rods may be cut for fit as necessary. Mounting: after assembling the lattice frame, there should be an equal number of remaining 4-foot rods, base plates and open connectors. Connect an open connector to one end of the 4-foot rod and a base plate to the other end. Attach the open connector to the lattice frame 90 degrees in a square or rectangular pattern (the base plate pointing to the back mounting surface). Base plates may be secured with #10 screws. Mounting Screws Not Included. Learn More -
6 Foot Aluminum Side, Top & Bottom Lab-Frame Kit.
Lee Engineering
$411.90
Special Price $325.00
This mounting option is recommended for situations when you need a lab support lattice to cover the entire back panel of your fume hood. Assembly Instructions: Lattice frame: Use the open connectors and lattice rods to assemble the frame. The kit assumes a lattice spacing of 1-foot; however, this may vary depending on your application. Rods may be cut for fit as necessary. Mounting: Attach vertical base plates to the horizontal and vertical rod ends. Base plates may be secured with #10 screws. Mounting Screws Not Included. Learn More -
7 Foot Stainless Steel Side, Top & Bottom Lab-Frame Kit.
Lee Engineering
$1,068.86
Special Price $935.25
This mounting option is recommended for situations when you need a lab support lattice to cover the entire back panel of your fume hood. Lattice frame: Use the open connectors and lattice rods to assemble the frame. The kit assumes a lattice spacing of 1-foot; however, this may vary depending on your application. Rods may be cut for fit as necessary. Mounting: Attach vertical base plates to the horizontal and vertical rod ends. Base plates may be secured with #10 screws. Mounting Screws Not Included. Learn More -
4 foot Fiberglass Table Top Mount Lab-Frame Kit.
Lee Engineering
$453.86
Special Price $397.13
Lattice frame: Use the open connectors and lattice rods to assemble the frame. The kit assumes a lattice spacing of 1-foot and a border on the sides and top. Spacing may vary depending on your application. Rods may be cut for fit as necessary. Mounting: After assembling the lattice frame attach vertical base plates to the bottom of the vertical rods. There should be an equal number of remaining 2-foot rods, swivel base plates and open connectors. Connect an open connector to one end of the 2-foot rod and a swivel base plate to the other end. Attach the open connector to the lattice frame 30-45 degrees. Base plates may be secured with #10 screws. Mounting Screws Not Included. NOTE: Follow your fume hood manufacturers’ requirements for attachment. Learn More -
4 foot Back Mount Stainless Steel Lab-Frame Kit.
Lee Engineering
$479.71
Special Price $419.75
This mounting option is recommended for situations when you need a lab support lattice to cover the entire back panel of your fume hood. Lattice frame: use the open connectors and lattice rods to assemble the frame. Use one open connector at each rod intersection. The kit assumes a lattice spacing of 1-foot; however, this may vary depending on your application. Rods may be cut for fit as necessary. Mounting: after assembling the lattice frame, there should be an equal number of remaining 4-foot rods, base plates and open connectors. Connect an open connector to one end of the 4-foot rod and a base plate to the other end. Attach the open connector to the lattice frame 90 degrees in a square or rectangular pattern (the base plate pointing to the back mounting surface). Base plates may be secured with #10 screws. Mounting Screws Not Included. Learn More -
4 foot Aluminum Table Top Mount Lab-Frame Kit
Lee Engineering
$350.43
Special Price $306.63
Lattice frame: Use the open connectors and lattice rods to assemble the frame. The kit assumes a lattice spacing of 1-foot and a border on the sides and top. Spacing may vary depending on your application. Rods may be cut for fit as necessary. Mounting: After assembling the lattice frame attach vertical base plates to the bottom of the vertical rods. There should be an equal number of remaining 2-foot rods, swivel baseplates and open connectors. Connect an open connector to one end of the 2-foot rod and a swivel base plate to the other end. Attach the open connector to the lattice frame 30-45 degrees. Base plates may be secured with #10 screws. Mounting Screws Not Included. NOTE: Follow your fume hood manufacturers’ requirements for attachment Learn More -
7 Foot Fiberglass Side, Top & Bottom Lab-Frame Kit.
Lee Engineering
$553.14
Special Price $484.00
This mounting option is recommended for situations when you need a lab support lattice to cover the entire back panel of your fume hood. Assembly Instructions: Lattice frame: Use the open connectors and lattice rods to assemble the frame. The kit assumes a lattice spacing of 1-foot; however, this may vary depending on your application. Rods may be cut for fit as necessary. Mounting: Attach vertical base plates to the horizontal and vertical rod ends. Base plates may be secured with #10 screws. Mounting Screws Not Included. Learn More