Supplies

Size: for standard Over Head Drive 15l vessel To fit gl45 vertical sidearms Material: 316l SST with electropolish finish, ra 32 or better, inside & out Dimensions:harvest tube (3/8"od)-1"above slug,16" insertion length, approx Additon tube (1/4"OD) - 1" above slug, 2 21/64" below Vent tube (1/4" OD) - 1" above slug, .975" below Supply with 45mm PP blue open top screw cap & white silicone gasket (1 per EA )

Stainless steel rocker platform fit Bellco micro and mini ovens. Platform has 3 settings at 2.5 degree to 6 degrees from horizontal and adapts to existing rotisserie hardware. (1 per EA )

Will not rust or deteriorate in water baths or co2 atmospheres. Manufactured from 303 stainless steel with electropolish finish. Each opening rack 1 1/16" (26.9mm) Tube size: 25mm Spacing:4x10 holds 40 tubes Dimensions: 11 1/2" x 4 3/4" x 4" WIRE SPECIFICATIONS: SIDE & UPRIGHTS: .162"OD WIRE, CROSS WIRE: 0.063" OD WIRE, BTTM MESH: 1/4" Minimum order requirement: 5 each (1 per EA )

4" od 316l stainless steel, ra32 finish or better Marine impeller with 1/2" bore & set screw. (1 per EA )

Material: 316L SST with Ra Finish 32µ or better - inside & out Tubing Specifications: .250" OD x .152" ID Vent Port: 1.0" long - above & below cap slug Addition Port: 1.0" long above cap slug & 16 1/14"(approx) below cap slug Media Port: 1.0" long above cap slug with 1 3/4" bend radius & 12 25/32" long Ten (10) drilled holes (.040"). Supply Cap & Liner (1 per EA )

Manufactured from type 1 class a Borosilicate glass. Bottom indent and 3 vertical baffles for optimal mixing. Sidearm cap: 32mm Center cap: 70mm Dimensions: 150" x 85" Flask size: 250ml (1 per EA )

Glass shaft impeller assembly for 1967-style hanging bar spinner flask. Consist of ptfe magnet holder and ptfe coated magnet. Glass shaft ptfe magnet Size: 50-500ml CONSIST OF: PTFE MAGNET HOLDER and PTFE COATED MAGNET (1 per EA )

Designed for growing insect cell cultures such as SF9 and SF21 cells. The system comes complete with all accessories needed to grow your insect culture line for expression Includes: –7785-D2005 Digital 5-Position Magnetic Stirrer 115V –1965-03000 Micro-Carrier Spinner Flask Complete 3L –1965-20003R 2-Port Assembly 3L –7808-10004 Gas Blending Stand –7725-00120 Air Supply Pump 115V –7800-10050 Silicone Tubing 1/4” ID (1 per EA )

Bellco manufactures all precision pipettes from type 1 class a Borosilicate glass. All bellco pipettes feature tempered tips and permanent silk screened graduations to withstand repeated usage and alkali washings. Plain top promotes rapid & even flow. (18 per CS )

Ideal use for Biometer flask. Consist of: needle and stopper Packed 1 per case (1 per EA )

MICROCARRIER SPINNER FLASKS -PROMOTES OPTIMAL GROWTH OF SUSPENSION AND MICROCARRIER CULTURE -IMPELLER HEIGHT ADJUSTS THROUGH COMPRESSION FITTING -INDENTED BOTTOM (UP TO 1L) PREVENTS ACCUMULATION OF MICROCARRIER BEADS UNDER IMPELLER OD X OAH:410 X 545 (with cap) CAP:100MM SIDEARM:45MM (1 per EA )

Stainless Steel Shaft Assembly The Bellco Stainless Steel Shaft Conversion Kit is designed to convert your standard glass shaft to stainless steel on 1967 and 1965 Spinner Flasks. Sizes range from 100 mL to 36 liters for 1965 spinners and 100 to 3000 mL for 1967 spinner flasks. Material: 316L Stainless Steel and polypropylene compression fitting. Size: 250ml (1 per EA )

Manufactured from Type 1 Class A Borosilicate Glass. Shake flasks are the basic tool for growth studies of aerobic microbial cultures. They have rigidly controlled baffle angles and depths to promote optimal oxygen transfer while reducing vortex formation. Designed for all orbital shakers. Specifications: Type 1 Class A Borosilicate Glass Sizes: 500mL Closure Sizes: 38mm OD x OAH: 100 x 205mm DeLong Style Neck Case Quantity: 2543-00500: 12 (12 per CS )

• Material: Type 1 Class A Borosilicate Glass • Dimensions: 63.5mm OD x 135mm Overall Height • Graduations: 20mL – 100mL, every 20mL • Bottom indents and three vertical baffles for optimal mixing • Two 32mm Side arms angled 45° off center for Port Assemblies • One 70mm Screw Thread Center Neck • Rugged stainless steel/ PTFE Internal Bearing Assembly • Supply with: Two 32mm PP Blue Screw Caps (1 per EA )

Bell-ennium Magnetic Stirrers are designed for both cell cultures in spinner flasks as well as for general laboratory procedures requiring the use of magnetic stirring equipment. Bell-ennium stirrers offer the laboratory researcher a wide range of capabilities and the latest innovations in stirring technology. Bell-ennium stirrers feature brushless maintenance free DC motors with drive assemblies designed for quiet operation. Stainless steel covers are stamped to show the vessel positions for accurate placement and optimum performance. The Bell-ennium single position low profile chassis measure 10 x 11 x 3 3/8” and are designed to fit side-by-side in Bellco incubators. Units are powered by standard 24V in-line power supplies and are CE compliant. (1 per EA )

Bellco manufactures all precision pipettes from type 1 class a Borosilicate glass. All bellco pipettes feature tempered tips and permanent silk screened graduations to withstand repeated usage and alkali washings. (18 per CS )

Type 1 class a Borosilicate glass for freeze drying or cryogenic storage. The neck has pre-drawn constriction to facilitate sealing. Flat bottom Constriction neck Neck od: 9mm Bottom od: 12mm Capacity: 2ml Length: 145mm (144 per CS )

Type 1 Class A Borosilicate Glass 19L #12 Stopper Neck 292mm OD x 485mm OAH (1 per EA )

Manufactured from type 1 class a Borosilicate glass. Non-corrosive Borosilicate glass to prevent etching. Accepts bellco stainless steel closures and kaput closures. Round bottom Sizes: 25x150mm Volume: 55.6ml Closure: 25mm (72 per CS )

Large flange air stone sparger for large flange vessels. Fits through stainless steel head plate fitting. These spargers fit through a 5/16" fitting. 316 l stainless steel Ra 32 finish or better Acrodisc filter assembly, 0.2 micron (1 per EA )

Manufactured from Type 1 Class A Borosilicate Glass. Ideal for use of filling other glass vessels. Receiving vessel is placed under bell to maintain aseptic conditions during filling. Attaches to reservoir with rubber tubing. Specifications: Type 1 Class A Borosilicate Glass Dimensions: 41x95mm Tubing Size: 1/4" 2 per case (2 per CS )

The Bellco Auto-blot Micro Hybridization Oven consists of an incubator with an integral rotisserie device. The rotisserie has the capacity for up to 4 large hybridization bottles or 8 small hybridization bottles. Alternatively, any combination of large or small bottles can be used. This Auto-blot Micro Hybridization Oven features an advanced temperature controller for precise control of oven temperature. Ext: 14”x17”x13” (35x42x32cm) Int: 7”x15”x8” (18x37x20cm) 100v. (1 per EA )

Used to surround a single cell to create homogeneous culture of cells rather than mixed population. The flat end ensures tight sealing with surface of culture dish. Sizes: 6x8mm (125 per CS )

Manufactured from Type 1 Class A Borosilicate Glass with a low coefficient of expansion. Heavy wall beakers meet astime-960 type 1 specifications for classification design capacity and markings. Features a easy pour spout, white permanent graduations and a large marking square. Specifications: Type 1 Class A Borosilicate Glass Size: 1L Dimensions: 110 x 145mm Case Quantity: 3 (3 per CS )