Supplies

Manufactured from Type 1 Class A Borosilicate Glass. Shake flasks are the basic tool for growth studies of aerobic microbial cultures. They have rigidly controlled baffle angles and depths to promote optimal oxygen transfer while reducing vortex formation. Designed for all orbital shakers. Break resistant lip to prevent chipping. Specifications: Type 1 Class A Borosilicate Glass Size: 250ml Dimensions: 80x140mm Case Quantity: 12 Baffle Dimensions: 6mm x35° (12 per CS )

Will not rust or deteriorate in water baths or co2 atmospheres. Manufactured from 303 stainless steel with electropolish finish. Each opening rack 13/16" (20.6mm) Tube size: 20-22mm Spacing: 6x12 holds 72 tubes Dimensions: 275 x 150 x 80mm WIRE SPECIFICATIONS: SIDE & UPRIGHTS: .135"OD WIRE, CROSS WIRE: 0.063" OD WIRE, BTTM MESH: 1/4" Minimum order requirement: 5 each (1 per EA )

Stainless Steel Hi-Torq Over Head Drive Impeller Full Width 8L Specifications: Hi-Torq SST Over Head Drive Impeller Assembly – Full Width Size: 8L . For Hi-Torq Motor & Cap Assembly (7774-40115/40230 & 7764-74000) Similar To 1964-60008 But To Accept 1/2" Shaft From 7764-74000 Cap Assembly Material: 316L SST With Elelctropolish Finish Ra32 Or Better Paddle Size: 3" Tall X 8" Wide (1 per EA )

The stainless steel 100mm IOB probe cap seal is manufactured from 316L stainless steel and has a red-silicone sealing gasket with a 100mm blue polypropylene screw cap. The stainless steel probe cap seal has four accessory ports surrounding a centrally located internal impeller assembly. Two of these ports have a white silicone plug inside a threaded cap that acts as a compression fitting for probe insertion. The other ports accept accessories using the same silicone compression plugs and threaded caps. These compression plugs make it easy to adjust the insertion length of probes or straight tubes depending upon the working volume of the bioreactor flask. The stainless steel cap seal, stainless steel PTFE impeller and all fittings are steam autoclavable. (1 per EA )

The Bellco Auto-blot Mini Hybridization Oven consists of an incubator with an integral rotisserie device. The rotisserie has the capacity for up to 4 large hybridization bottles or 8 small hybridization bottles. Alternatively, any combination of large or small bottles can be used. This Auto-blot Micro Hybridization Oven features an advanced temperature controller for precise control of oven temperature. 14”x17”x13” (35x42x32cm) 230v (1 per EA )

Ideal for growing, storing and mixing or aerobic and anaerobic cultures. Threaded neck and sidearm with clean-out port. Supplied with 38mm and 18mm rubber lined black phenolic screw caps. Specifications: Type 1 Class A Borosilicate Glass Sizes: 1L Includes: 38mm And 18mm Black Phenolic Screw Caps Sidearm Dimensions: 14x130mm m Case Quantity: 4 (4 per CS )

Manufactured from type 1 class a Borosilicate glass. Ideal for growing, storing and mixing of aerobic and anaerobic cultures. Graduated to approximate volumes Size: 3l Closure: 38 Dimensions: 184x340 (3 per CS )

Will not rust or deteriorate in water baths or co2 atmospheres. Manufactured from 303 stainless steel with electropolish finish. Each opening rack 15/16" (23.8mm) Tube size: 20-22mm Spacing:4x10holds 40 tubes Dimensions: 9 11/16" X 3 15/16" X 3 1/8" WIRE SPECIFICATIONS: SIDE & UPRIGHTS: .135"OD WIRE, CROSS WIRE: 0.063" OD WIRE, BTTM MESH: 1/4" Minimum order requirement: 5 each (1 per EA )

Description: Glass Ball Spinner Flask Only Size: 250mL Material: Type 1 Class A Borosilicate Glass Dimensions: 85mm OD x 140mm Overall Height, 164mm across sidearms Two 32mm Sidearms angled 55° offset center 70mm Screw Thread Center Neck Dimpled Bottom Graduations: 50mL to 250mL, every 25mL – White Ink (Approx Volumes) Supply with: Two 32mm PP Blue Screw Caps & PP Blue Pouring Rings (1 per EA )

Manufactured from type 1 class a Borosilicate glass. Designed with deep side baffles for optimal agitation. Large bottom surface for easy access with Bellco large orifice pipette. Break resistant lip Size: 125mL OD x OAH – 66 x 115mm 3 per case (3 per CS )

Heavy gauge rectangular construction for easy stacking and storage. These pipette cans can be sterilized by autoclave or dry heat. (do not exceed 400 degrees F). Includes silicone pad on the inside of top and bottom to protect pipette tips. --Satin finish surface of entire can for convenient marking or coding. --Silicone pads on inside of top and bottom protect pipette tips. --Material: 304 stainless steel .031” thick (1 per EA )

Ideal for growing, storing and mixing or aerobic and anaerobic cultures. Threaded neck and sidearm with clean-out port. Supplied with 38mm and 18mm rubber lined black phenolic screw caps. Specifications: Type 1 Class A Borosilicate Glass Sizes: 500mL Includes: 38mm And 18mm Black Phenolic Screw Caps Sidearm Dimensions: 19x130mm Case Quantity: 4 (4 per CS )

Will not rust or deteriorate in water baths or co2 atmospheres. Manufactured from 303 stainless steel with electropolish finish. Each opening rack 1 9/16" (39.6mm) Tube size: 38mm Spacing: 3x4 holds 12 tubes Dimensions: 6 3/4" x 5 1/8" x 5" WIRE SPECIFICATIONS: SIDE & UPRIGHTS: .162"OD WIRE, CROSS WIRE: 0.063" OD WIRE, BTTM MESH: 1/4" Minimum order requirement: 5 each (1 per EA )

Thermowell assemblies are used to hold inside one tube the rtd temperature sensor that monitors the temperature within the vessel in conjunction with a temperature controller. There are also tubes for addition of media and vent tube • Thermowell assemblies for 1965 and 1967-style angled sidearm flasks, 3-port • 5/16" od thermowell tube,1/4" siphon and vent tubes • Includes 45mm pp cap and silicone gasket • Seam welded and electropolished finish - outside only • All tubes: 316l sst • Longest tube length @ curve: 10 1/2" (1 per EA )

Manufactured from 1 Borosilicate glass Accepts bellco glass inc stainless steel kap-uts closures Closure size 38mm (36 per CS )

Manufactured from type 1 class a Borosilicate glass. Ideal for growing, storing and mixing of aerobic and anaerobic cultures. Graduated to approximate volumes Size: 125ml Closure: 25 Dimensions: 66x136mm (12 per CS )

Manufactured for type 1 class a Borosilicate glass. Ideal for growing, storing, and mixing of aerobic and anaerobic cultures. Graduated to approximate volumes. Size: 25ml Closure: 18 Dimensions: 40x96mm Stainless steel closure or Kaput closure sold separately (24 per CS )

Manufactured from Type 1 Class A Borosilicate Glass. Designed for culturing organisms that require a large surface area to volume ratio. Flask is supplied with a GL45 blue polypropylene linerless screw cap and pouring ring. Specifications: Type 1 Class A Borosilicate Glass Sizes: 2800ml OD X OAH (MM):210 X 225 Case Quantity: 1 (1 per EA )

Manufactured from Type 1 Class A Borosilicate Glass. Designed for culturing organisms that require a large surface area to volume ratio. Flask is supplied with a GL45 blue polypropylene linerless screw cap and pouring ring. Specifications: Type 1 Class A Borosilicate Glass Sizes: 1800ml OD X OAH (MM):200 X 157 Case Quantity: 1 (1 per EA )

45mm low profile Thermowell assembly for low profile 3l vessel. Seam welded - electropolish finish 316l stainless steel material ra 32 finish or better Supply with s/cap (a523-599) & white silicone liner (a523-600) 1 - THERMOWELL TUBE: 5/16"OD X .242"ID X 1.0" above x 8 11/32" insertion 1- FILL TUBE: 1/4"OD X .152"ID X 1.0" above x 8 11/32" insertion 1- VENT TUBE: .250"OD X .152"ID X 1.0"LONG (1 per EA )

Will not rust or deteriorate in water baths or co2 atmospheres. Manufactured from 303 stainless steel with electropolish finish. Each opening rack 9/16" (14.3mm) Tube size: 13mm Spacing: 3x4 holds 12 tubes Dimensions: 2 3/4" x 2 1/16" x 2" WIRE SPECIFICATIONS: SIDE & UPRIGHTS: .135" OD, CROSS WIRE: 0.063" OD, BTTM MESH: 1/4" Minimum order requirement: 5 each (1 per EA )

Will not rust or deteriorate in water baths or co2 atmospheres. Stainless steel material Each opening rack 9/16" (14.3mm) Tube size: 13mm Spacing: 4x10 holds 40 tubes Dimensions: 6 1/2" x 2 3/4" x 2" WIRE SPECIFICATIONS: SIDE & UPRIGHTS: .135" OD WIRE, CROSS WIRE: 0.063" OD WIRE, BTTM MESH: 1/4" Minimum order requirement: 5 each (1 per EA )

Probe adapters & compression fittings. Bellco compression fittings are designed using our standard 45 mm blue polypropylene open top caps and white silicone gaskets. A wide variety of fittings are available to allow pH and do monitoring via insertion of these probes into the sidearms of vessels. Bellco probe adapters are designed to allow introduction of threaded probes into vessels through 200 mm stainless steel headplate or a 45 mm vertical sidearm. Probe OD: 1/2" Stainless steel fitting w/ cap ½" (1 per EA )

Round bottom type 1 class a Borosilicate glass. Includes 38mm phenolic screw cap. 38x200mm. (36 per CS )