Reusable Glassware

The Bellco low profile ptfe impellers are designed to be used with bellco low profile cell culture vessels. These low profile impeller consist of a semi-rigid ptfe blade, ptfe paddle holder and stainless steel shaft. Impellers are shipped fully assembled. Paddle Size: 3"Tx 6 3/4"W. Requires Bellco Overhead Drive & Cap Assembly (1 per EA )

VERTICAL DISK IMPELLER 3L Material: 316 SST For bioreactor system - 7802-03115 Dimensions: 2" od x 47/64" wide For .375" od shafts (1 per EA )

Manufactured from type 1 class a Borosilicate glass. Bottom pad prevents chipping and breaking of pipette tips. All components can and will withstand repeated dry or steam heat serialization. Supplied stainless steel closure. Case qty-6 (6 per CS )

Sparger assembly for 6l low profile Over Head Drive vessel. This fits through a 45mm sidearm. Designed for vertical side arm vessels. Sparger tube: 10 1/8" long 316 l SST 20 ra material. 12mm od coarse glass frit (40-60µ) Gently introduces bubbles into vessel. (1 per EA )

Ideal for use with water baths for precise temperature control. Supplied with 100mm center cap, sidearms cap, and pouring ring. Specifications: #4 Hose Barbs For 1/2" Id Tubing Material: Type 1 Class A Borosilicate Glass Supplied: 45mm Polypropylene Blue Cap & Pouring Ring Size 6L OD x OAH: 300x325mm (1 per EA )

Promotes optimal growth of suspension and micro-carrier culture. Impeller height adjust through compression fitting center cap. The indented bottom prevents accumulation of micro-carrier beads under impeller. Size: 250ml Sidearm cap: 32mm (included) (1 per EA )

Will not rust or deteriorate in water baths or co2 atmospheres. Manufactured from 303 stainless steel with electropolish finish. Each opening rack 13/16" (20.6mm) Tube size: 20-22mm Spacing: 6x12 holds 72 tubes Dimensions: 275 x 150 x 80mm WIRE SPECIFICATIONS: SIDE & UPRIGHTS: .135"OD WIRE, CROSS WIRE: 0.063" OD WIRE, BTTM MESH: 1/4" Minimum order requirement: 5 each (1 per EA )

Stainless Steel Hi-Torq Over Head Drive Impeller Full Width 8L Specifications: Hi-Torq SST Over Head Drive Impeller Assembly – Full Width Size: 8L . For Hi-Torq Motor & Cap Assembly (7774-40115/40230 & 7764-74000) Similar To 1964-60008 But To Accept 1/2" Shaft From 7764-74000 Cap Assembly Material: 316L SST With Elelctropolish Finish Ra32 Or Better Paddle Size: 3" Tall X 8" Wide (1 per EA )

The stainless steel 100mm IOB probe cap seal is manufactured from 316L stainless steel and has a red-silicone sealing gasket with a 100mm blue polypropylene screw cap. The stainless steel probe cap seal has four accessory ports surrounding a centrally located internal impeller assembly. Two of these ports have a white silicone plug inside a threaded cap that acts as a compression fitting for probe insertion. The other ports accept accessories using the same silicone compression plugs and threaded caps. These compression plugs make it easy to adjust the insertion length of probes or straight tubes depending upon the working volume of the bioreactor flask. The stainless steel cap seal, stainless steel PTFE impeller and all fittings are steam autoclavable. (1 per EA )

The Bellco Auto-blot Mini Hybridization Oven consists of an incubator with an integral rotisserie device. The rotisserie has the capacity for up to 4 large hybridization bottles or 8 small hybridization bottles. Alternatively, any combination of large or small bottles can be used. This Auto-blot Micro Hybridization Oven features an advanced temperature controller for precise control of oven temperature. 14”x17”x13” (35x42x32cm) 230v (1 per EA )

Description: Glass Ball Spinner Flask Only Size: 250mL Material: Type 1 Class A Borosilicate Glass Dimensions: 85mm OD x 140mm Overall Height, 164mm across sidearms Two 32mm Sidearms angled 55° offset center 70mm Screw Thread Center Neck Dimpled Bottom Graduations: 50mL to 250mL, every 25mL – White Ink (Approx Volumes) Supply with: Two 32mm PP Blue Screw Caps & PP Blue Pouring Rings (1 per EA )

Manufactured from type 1 class a Borosilicate glass. Designed with deep side baffles for optimal agitation. Large bottom surface for easy access with Bellco large orifice pipette. Break resistant lip Size: 125mL OD x OAH – 66 x 115mm 3 per case (3 per CS )

45mm low profile Thermowell assembly for low profile 3l vessel. Seam welded - electropolish finish 316l stainless steel material ra 32 finish or better Supply with s/cap (a523-599) & white silicone liner (a523-600) 1 - THERMOWELL TUBE: 5/16"OD X .242"ID X 1.0" above x 8 11/32" insertion 1- FILL TUBE: 1/4"OD X .152"ID X 1.0" above x 8 11/32" insertion 1- VENT TUBE: .250"OD X .152"ID X 1.0"LONG (1 per EA )

Probe adapters & compression fittings. Bellco compression fittings are designed using our standard 45 mm blue polypropylene open top caps and white silicone gaskets. A wide variety of fittings are available to allow pH and do monitoring via insertion of these probes into the sidearms of vessels. Bellco probe adapters are designed to allow introduction of threaded probes into vessels through 200 mm stainless steel headplate or a 45 mm vertical sidearm. Probe OD: 1/2" Stainless steel fitting w/ cap ½" (1 per EA )

For use circulating water bath or chiller and magnetic stir plate. Hose connection accepts 3/8" ID silicone tubing (Bellco M7965037) Available complete with micro-carrier impeller assembly or as components. Specifications: Jacket Volume (mL): 75ml Cap Size: 70mm Sidearm Cap Size (mm): 18 OD x OAH: 75x160mm (1 per EA )

Stainless steel shaft design prevents cell damage and minimizes magnetic decoupling. Sealed internal assembly requires less incubator space. For use with Bellco 1965-series Standard and Water Jacketed Spinner Flasks. Specifications: Cap Size: 70mm Flask Size: 100mL – 250mL Paddle: 2" x 1.5" (1 per EA )

The Bellco Process Controlled Bottom Drive Roller Apparatus holds up to 50 (see specifications below) full size glass or plastic roller bottles (110 to 120 mm diameter and up to 510 mm in length). The unit features a brushless DC motor and controller that operate at bottle speeds ranging from 0.3 to 9.0 rpm with the ability to select clockwise or counter clockwise direction. Units feature brushless, maintenance-free DC motors with drive assemblies designed for quiet operation. Four corner bumpers and two locking castors (on the front wheel positions) are also provided. Rollers are easily removed for replacement by using the special tool provided with each unit. All-Position Drive facilitates the use of lightweight plastic roller bottles by ensuring rotation at each bottle station, independent of any load configurations. (1 per EA )

The Bellco Top Drive Roller Apparatus has been designed for production of animal cells, viruses and cell products. The unit accommodates 53 bottle positions with over 85,000 cm2 of surface area. Rollers have a key design to eliminate slipping and are easily removable for servicing of bearings. Rollers are formulated from a chemical-resistant non-slip EDPM. All units incorporate a solid state control with a brushless motor and controller, providing smooth operation and easy maintenance. All units feature rubber bumpers, handles, a slotted rear guard, and All Position Drive. The All Position Drive is designed to accommodate plastic roller bottles by preventing the slipping of the light-weight bottles. An optional Motion Alarm System provides audible and visual alarms should the primary fail. (1 per EA )

The Bellco Refrigerated Roll-In Incubators have 40 cubic feet of volume and are designed for use with Bellco’s Cell Production Roller Apparatus (CPRA). The flush-to-floor design allows easy movement of the CPRA in and out of the chamber. Four internal convenience outlets allow simple connection for internally placed appliances such as CPRA, Roller Drums, Magnetic Stirrers, etc. Shelf brackets are included for mounting optional shelves to hold these appliances. Fans take air from the chamber top, pass it over the 1100 watt heater and inject it into the chamber on the bottom back wall. When the refrigeration mode is active, the air is cooled using a thermoelectric cooler. A microprocessor temperature controller and membrane keypad allows simple setting and monitoring of chamber temperature. The control panel contains indicator lights and dials for controlling temperature. A safety thermostat is included to prevent over-temperature failures. The unit is not intended for use with CO2 environments. (1 per EA )

Low profile 45mm 3-port assembly for vertical low profile3L vessels Seam welded - electropolish 316l stainless steel material All tubes .250"od x .152"id Siphon tube: (long tube) 9 1/2", FILL TUBE: 3 13/16", VENT TUBE:2 5/32". SUPPLY WITH S/CAP (A523-599) & WHITE SILICONE LINER (A523-600) (1 per EA )

Manufactured from type 1 class a Borosilicate glass. For spinner flasks 6l to 8l Dimensions: 9mm x 400mm long (1 per EA )

Description: Glass Ball Spinner Comp, 8000mL Size: 8000mL Material: Type 1 Class A Borosilicate Glass Flask Dimensions: 238mm OD x 420mm OAH, two 45mm sidearms offset at 30º, 100mm center neck Includes two 45mm blue PP screw caps & two 45mm blue PP pouring rings Impeller Assembly: one 100mm blue PP screw cap, 100mm Teflon cap seal, 100mm blue silicone sealing gasket, soft silicone flex tube, glass ball magnet tube, and magnet Specially Formed Bottom Indent Prevents Accumulation under impeller Glass ball houses a magnet for gentle agitation of Micro carrier Beads (1 per EA )

The Bellco Cell Production Roller Apparatus has been designed for production of animal cells, viruses and cell products. Modular units are available from 5 to 45 bottle positions and allow easy expansion with modular add-on decks. Non-modular production units come in 45 and 50 bottle positions with over 80,000 cm2 of surface area. Rollers have a key design to eliminate slipping and are easily removable for servicing of bearings. Rollers are formulated from a chemical-resistant non-slip EDPM. All units feature a solid state control with heavy-duty DC motor and analog tachometer. Non-modular production models feature rubber bumpers, handles and a slotted rear guard. (1 per EA )

Manufactured from Type1 Class B Borosilicate Glass. Large opening and sloping shoulders facilitate pouring and cleaning. Heavier walls prevent breakage of glass. Media storage bottles have white graduations and a marking area. They are supplied with rubber lined black phenolic screw cap. Specifications: Type 1 Class B Borosilicate Glass Sizes: 1L (33)mm Cap OD x OAH: 103 x 231 Case Quantity: 6 (6 per CS )