Glassware

Probe adapters & compression fittings. Bellco compression fittings are designed using our standard 45 mm blue polypropylene open top caps and white silicone gaskets. A wide variety of fittings are available to allow pH and do monitoring via insertion of these probes into the sidearms of vessels. Bellco probe adapters are designed to allow introduction of threaded probes into vessels through 200 mm stainless steel headplate or a 45 mm vertical sidearm. Probe OD: 11mm Stainless steel fitting w/cap 11mm (1 per EA )

Internal impeller decreases risk of contamination. Impeller has an adjustable shaft to align paddle. The large paddle promotes increased oxygenation. Cap size: 100mm Flask size: 1l Dimensions: 135 x 250mm Sidearm cap: 45mm (1 per EA )

• Designed for the efficient growth of suspension cells at low speeds • Flask Specifications: o 250 mL flat bottom, Type 1 Class A Borosilicate o Dimensions: 85mm OD x 145mm OAH o Two 32mm Sidearms angled 55º offset center o One 70mm Screw thread center neck o Graduations: 50mL to 250mL, every 25mL o Includes two 32mm blue PP screw caps and pouring rings • Impeller Assembly Specifications: o Consists of PTFE coated magnet and white Teflon magnet holder • Glass Shaft Specifications: o Type 1 Class A Borosilicate o Dimensions: 7mm OD x 155mm long • Cap Assembly Specifications: o Consists of one 70mm blue PP screw cap with 16.2 mm hole for black compression fitting, 70mm white silicone liner with 15.8mm hole, 7mm black compression fitting (1 per EA )

Manufactured from type 1 class a Borosilicate glass. Supplied with a 38-400 black phenolic rubber lined screw cap. Dimensions: 96x173mm Size: 590ml (4 per CS )

Manufactured from Type 1 Class A Borosilicate Glass with a low coefficient of expansion. Heavy wall beakers meet astime-960 type 1 specifications for classification design capacity and markings. Features a easy pour spout, white permanent graduations and a large marking square. Specifications: Type 1 Class A Borosilicate Glass Size: 250mL Dimensions: 70 x 87mm Case Quantity: 12 (12 per CS )

The Bellco Cell Production Roller Apparatus has been designed for production of animal cells, viruses and cell products. Modular units are available from 5 to 45 bottle positions and allow easy expansion with modular add-on decks. Non-modular production units come in 45 and 50 bottle positions with over 80,000 cm2 of surface area. Rollers have a key design to eliminate slipping and are easily removable for servicing of bearings. Rollers are formulated from a chemical-resistant non-slip EDPM. All units feature a solid state control with heavy-duty DC motor and analog tachometer. Non-modular production models feature rubber bumpers, handles and a slotted rear guard. (1 per EA )

The Bellco Cell Production Roller Apparatus has been designed for production of animal cells, viruses, and cell products. Modular units are available from 5 to 45 bottle positions and allow easy expansion with modular add-on decks. Non-modular production units come in 45 and 50 bottle positions with over 80,000 cm2 of surface area. Rollers have a key design to eliminate slipping and are easily removable for servicing of bearings. Rollers are formulated from a chemical-resistant non-slip EDPM. All units feature a solid state control with heavy-duty DC motor and digital display. All Position Drives are for use with plastic roller bottles to prevent slipping of the light-weight bottles. Roller Shaft Construction: Non-transferring chemical-resistant rubber rollers with key-shape. Clearance between Decks for Bottle Placement: 134 mm. Construction Material: Aluminum, enamel finish. Usable Roller Length: 51 cm. Brushless motor with controller for smooth operation and no maintenance. Easy-to-remove roller bar assembly (tool provided). Digital LCD display. Locking speed control knob. All position drives. Accepts all Bellco Roller Bottles (glass or plastic* in 110mm or 120mm diameter). Battery backup provides 18 hour service (typical at 2 RPM). Battery backup includes both audible and visual indicators. Motion Alarm (1 per EA )

The Bellco Bench top Modular Roller Apparatus is a variable speed two bottle roller apparatus (expandable to six bottles) used for the purpose of producing animal cells or cell products. This small sized unit is ideal for experimental and pilot-scale cell culture. The unit features a heavy-duty DC motor and solid-state electronics for reliable operation. The unit includes All-Position Drive belts so that every roller rotates, thus preventing slippage of light-weight plastic bottles. Bellco’s unique hex-shaped shafts prevent roller slippage and produce positive drive. (1 per EA )

Deck only for bench-top modular roller apparatus 7632-00115 & 7632-00230. 2 position Deck to deck spacing: 7" (1 per EA )

HTS Accessory Tray,12" x 12" for Micro-plates. Dimensions: 30 x 30cm Holds 24 micro-plates (1 per EA )

H/S Vertical Lift Impeller-5L Complete. Consists Of: 7764-75008 & 7764-76005. Dimensions: (Shaft); 5/8"OD X 14" Long., (Disk); 3" OD. 316L Sst (1 per EA )

H/S Vertical Lift Impeller-15L Complete. Consist Of; 7764-75015 & 7764-76015. Dimensions: (Shaft); 5/8"OD X 20 3/4" Long, (Disk); 3 3/4" OD. 316L Sst (1 per EA )

Triple Addition Assembly. For GL45 sidearms. Manufactured from 316l stainless steel with electropolish finish ra 32 or better inside and out. Supply with PP blue Open top s/cap & white silicone liner. All tubes: 1/4" OD x 4 1/4" long. Inseration Length: 3 3/32". Application: Individual ports for liquid additions or redundant vent/overlay. Vertical Side Arm vessels for acid, base, antifoam, media & other additions. (1 per EA )

Adjustable Hanging Bar Spinner Flask without Bottom Dimple PTFE impeller assembly rides on glass bearing for friction free operation. 25 & 50mL have black phenolic rubberlined center and sidearm caps. 100mL-300mL have polypropylene caps, silicone gasket and pouring rings accumulation of microcarrier beads under impeller. 50mL. Center cap: 51mm, side arm 18mm. Dimensions: 55 OD x 110 OAH (1 per EA )

Stirring rods are made of soft flint glass with both ends fire-polished and rounded (144 per PK )

Short Path Distillation Apparatus Utilizes a thermometer bulb as column packing. Compact head and condenser. Cow type receiver for best product recovery. Pear shaped flask has [Standard Taper] 10/18 side arm for bleed tube. 14/20 [Standard Taper] joints. #1 Hose connections. 190Hx215Wmm. (1 per EA)

Tubes Drying U-Shaped Full Length [standard taper] Joint [standard taper] Joint 24/40. Approx. Overall Height x Width (mm) 185 x 80 Inner joint at the bottom with a bulb desiccant chamber. Unit is supplied with a vent tube as illustrated. (1 per EA)

Tubes Culture Disposable Borosilicate Glass Size (mm) 16 x 150 Kimble round bottom culture tubes are available in borosilicate or flint glass. Tubes are annealed to reduce breakage along stress points and feature smooth tops and bottoms to prevent cuts.

Wide-Tip Volumetric Pipets, 50 mL (6 per PK )

Made from clear flint glass (1.8 to 2.0 mm thick), fine ground and polished edges. (12 per PK )

These Type 3 serological pipettes are made from borosilicate glass and comply with USP standards. Color-coded. Individually serialized and certified. Calibrated to deliver. Printed with durable amber markings. (5 per PK )

SerologicalLOGICAL PIPETTE,BULK-PAK, TD PLAIN TOP PROMOTES RAPID, EVEN FLOW CALIBRATED TO TIP TEMPERED TIP; TO DELIVER; BLOW OUT TOLERANCE +-ML):0.06 OAL (MM):350 COLOR CODE:ORANGE Case Qty: 250 (250 per CS )

Used to generate a localized cold surface on the exterior of the finger. Commonly used for sublimation, and can also be used in re-flux or distillation operations. 3L. (1 per EA )

Ideal for use with over head drive vessels. Manufactured from 316l electropolished stainless steel with 32ra finish or better. 1-siphon tube 15 5/8" long 1-fill tube 2 17/64" long 1-vent tube 1" long. 45mm 3-PORT ASSY FOR 1964 - STYLE OHD VESSEL, 8 & 15L. SUPPLY 45mM S/CAP (A523-599) & WHITE SILICONE LINER (A523-600). LENGTHS ARE MEASURED FROM TOP OF S/A TO BTTM OF TUBE (1 per EA )