Supplies

Ideal for use with water baths for precise temperature control. Supplied with 100mm center cap, sidearms cap, and pouring ring. 6 VERTICAL 45mm SIDEARMS. Material: type 1 class a Borosilicate glass. Dimensions: 300mm od x 280mm overall height Two (2) #4 hose connection (1 per EA )

Material: 316l SST with electropolish finish, ra 32 or better, inside & out Dimensions: harvest tube (3/8" od) - 1" above slug, 17" insertion length Addition tube (1/4"od) - 1" above slug, 2 21/64" below Vent tube (1/4" od) - 1" above slug, .975" below Supply with 45mm PP blue open top screw cap & white silicone gasket (1 per EA )

All port assemblies are manufactured from 316l stainless steel and have an electropolish finish. 2- port assemblies have siphon and vent tubes. 3-port assemblies have siphon, fill tube and vent tubes. All port assemblies include a 45mm blue polypropylene cap. (1 per EA )

For use circulating water bath or chiller and magnetic stir plate. Hose connection accepts 3/8" ID silicone tubing (Bellco M7965037) Available complete with micro-carrier impeller assembly or as components. Specifications: Jacket Volume (mL): 3700ml Cap Size: 100mm Sidearm Cap Size (mm): 45 OD x OAH: 200x445mm (1 per EA )

Stainless steel shaft design prevents cell damage and minimizes magnetic decoupling. Sealed internal assembly requires less incubator space. For use with bellco 1965-series standard and water jacketed spinner flasks Cap size: 70mm Flask size: 500m PADDLE: L X W:2 X 2 IN (1 per EA )

• Designed for the efficient growth of suspension cells at low speeds • Flask Specifications: o 100 mL flat bottom, Type 1 Class A Borosilicate o Dimensions: 63.5mm OD x 135mm OAH o Two 32mm Sidearms angled 55º offset center o One 70mm Screw thread center neck o Graduations: 20mL to 100mL, every 20mL o Includes two 32mm blue PP screw caps and pouring rings • Impeller Assembly Specifications: o Consists of PTFE coated magnet and white Teflon magnet holder • Glass Shaft Specifications: o Type 1 Class A Borosilicate o Dimensions: 7mm OD x 155mm long • Cap Assembly Specifications: o Consists of one 70mm blue PP screw cap with 16.2 mm hole for black compression fitting, 70mm white silicone liner with 15.8mm hole, 7mm black compression fitting (1 per EA )

316 L Stainless Steel Large Flange Drive Adapter for use with Omni Vessels. For attachment of Overhead Drive Motors. Heavy duty cap assembly for large flange vessels Adapt overhead drives to teflon or sst folding impeller assembly 316 sst design with polyester stainless steel bearings (1 per EA )

Bell-ennium Process Magnetic Stirrers are designed for both cell cultures in spinner flasks as well as for general laboratory procedures requiring the use of magnetic stirring equipment. The Front-End models are designed to position so that one flask is positioned behind the other, minimizing the width of the stirrer for limited space work areas. Bell-ennium stirrers feature brushless maintenance free DC motors with drive assemblies designed for quiet operation. Stainless steel covers are stamped to show the vessel positions for accurate placement and optimum performance. Heavy duty magnet assemblies provide the best magnetic coupling while timing belts on all positions insure smooth even stirring of vessel contents. The low profile chassis measure 11 x 20 x 3 3/8” and are designed to fit side-by-side in Bellco incubators. The PID process controller provides RS-485 communication with your existing lab network (software not included), as well as two alarm outputs for the optional Motion Alarm. Units are powered by standard 24V in-line power supplies and are CE compliant. (1 per EA )

Bellco Control System, Flat Bottom. The Bellco Stainless Steel Shaft Conversion Kit is designed to convert your standard glass shaft to stainless steel on 1967 and 1965 Spinner Flasks. Sizes range from: --100 mL to 36 liters for 1965 spinners --100 to 3000 mL for 1967 spinner flasks Material: --316L Stainless Steel 1965 & 1967 Series Micro-Carrier Spinner Flask 15L BCS Flat Bottom System 15L 115v (1 per EA )

The Bellco Auto-blot Micro Hybridization Oven consists of an incubator with an integral rotisserie device. The rotisserie has the capacity for up to 4 large hybridization bottles or 8 small hybridization bottles. Alternatively, any combination of large or small bottles can be used. This Auto-blot Micro Hybridization Oven features an advanced temperature controller for precise control of oven temperature. Without Rotisserie 14”x17”x13” (35x42x32cm) 230v (1 per EA )

Manufactured from type 1 class a Borosilicate glass. Specifications: Capacity: 80ml Dimensions: 55mm wide x 135mm long x 30mm deep Dam in bottle,, 25mm from bottom Neck size; 25mm Supplied with 25mm screw cap(2535-00025)& stopper (2048-11800) (1 per EA )

Promotes optimal growth of suspension and micro-carrier culture. Impeller height adjust through compression fitting center cap. The indented bottom prevents accumulation of micro-carrier beads under impeller. SIZE: 500ml (working volume). Dimensions: 110mm OD x 170mm overall height. Center neck: 100mm. Two 45mm angled sidearms; (ANGLED 60°). Grad. Range: 100-500ml, every 50ml. Supply with (2) 45mm PP blue screw caps & pouring rings. (1 per EA )

Polypropylene screw cap with silicone gasket pouring ring and compression fitting. 70mm (1 per EA )

Glass shaft impeller assembly for 1967-style hanging bar spinner flask. Consist of ptfe magnet holder and ptfe coated magnet. Glass shaft ptfe magnet Size: 25ml (1 per EA )

Ideal for growing, storing and mixing or aerobic and anaerobic cultures. Threaded neck and sidearm with clean-out port. Supplied with 38mm and 18mm rubber lined black phenolic screw caps. Specifications: Type 1 Class A Borosilicate Glass Sizes: 300mL Includes: 38mm And 18mm Black Phenolic Screw Caps Sidearm Dimensions: 14x130mm Case Quantity: 4 (4 per CS )

Ideal for growing, storing and mixing or aerobic and anaerobic cultures. Threaded neck and sidearm with clean-out port. Supplied with 38mm and 18mm rubber lined black phenolic screw caps. Specifications: Type 1 Class A Borosilicate Glass Sizes: 300mL Includes: 38mm And 18mm Black Phenolic Screw Caps Sidearm Dimensions: 19x130mm Case Quantity: 4 (4 per CS )

15L round bottom omni vessel 292 x 500mm Heavy walled construction for cell culture and fermentation applications. Heavy duty o-ring flange creates positive seal for stainless steel head-plate. For use with stainless steel head-plate, o-ring, and locking clamp. Use with series 500 controllers or with CellTrol (no speed) and OHD or high speed motor system. Use with 200mm large flange headplate (1 per EA )

Adjustable PTFE Microcarrier paddle blades only , 15-36L Paddle dimensions: 1 1/2" x 3 3/8" (1 per EA )

Bell-Flo IOB assembly was designed to be used with the bell-flo vessel with bottom indents and 3 vertical baffles for optimal mixing. Rugged stainless steel ptfe internal bearing impeller assemblies utilize a wing style impeller blade that increases mixing. CENTER CAP:70MM, SIDEARM CAP:32MM, -OAH X OD:130 X 65 (1 per EA )

Description: Glass Ball Impeller Assembly Only Size: 6000mL Screw Cap: Blue PP, 100mm OD x 22.4mm T Cap Seal: Teflon, 95.3mm OD x 10.4mm T Sealing Ring: Blue silicone rubber, 91.4mm OD x 76.2mm ID x 6.1mm T Flex Tube: Soft silicone, 108mm OAL, 0.312” OD x 0.248” ID Magnet Tube: Type 1 Class A Borosilicate Glass, 325mm OAL, 34mm OD ball, houses one cast alnico magnet (1 per EA )

Manufactured from type 1 class a Borosilicate glass, with a round bottom 38x200mm (36 per CS )

Manufactured for type 1 class a Borosilicate glass. Ideal for growing, storing, and mixing of aerobic and anaerobic cultures. Graduated to approximate volumes. Size: 4l Closure: 38 Dimensions: 205x370mm Stainless steel closure or Kaput closure sold separately (3 per CS )

Manufactured from type 1 class a Borosilicate glass. Includes long skirted black phenolic screw cap with white rubber liner. Screw cap included Size: 13 x 100mm Replacement cap: 2029-00013 (144 per CS )

SST Low Profile Impeller Assembly For 6000mL Low Profile Vessels. Requires Over Head Drive & cap assembly Material: SST 316l Consist of: dust shield, shaft, paddle, locking ring, washer, cotter pin Four (4) SST set screws: 8-32 x 1/4" Dimensions: 9 1/2" to 12 1/2" oal Paddle size: 3" tall x 5 1/4" wide Fully assembled (1 per EA )