Supplies

316-l stainless steel ra32 or better finish 10 micron porosity stainless steel frit for low profile vertical side arm vessels. Frit is removable for cleaning. Comes with 45mm blue polypropylene open top cap and silicone gasket Triple tube configuration With Vent, Fill/Sample And Sparge. (1 per EA )

The Bellco Process Controlled Bottom Drive Roller Apparatus holds up to 50 (see specifications below) full size glass or plastic roller bottles (110 to 120 mm diameter and up to 510 mm in length). The unit features a brushless DC motor and controller that operate at bottle speeds ranging from 0.3 to 9.0 rpm with the ability to select clockwise or counter clockwise direction. Units feature brushless, maintenance-free DC motors with drive assemblies designed for quiet operation. Four corner bumpers and two locking castors (on the front wheel positions) are also provided. Rollers are easily removed for replacement by using the special tool provided with each unit. All-Position Drive facilitates the use of lightweight plastic roller bottles by ensuring rotation at each bottle station, independent of any load configurations. (1 per EA )

The Bellco Cell Production Roller Apparatus has been designed for production of animal cells, viruses and cell products. Modular units are available from 5 to 45 bottle positions and allow easy expansion with modular add-on decks. Non-modular production units come in 45 and 50 bottle positions with over 80,000 cm2 of surface area. Rollers have a key design to eliminate slipping and are easily removable for servicing of bearings. Rollers are formulated from a chemical-resistant non-slip EDPM. All units feature a solid state control with heavy-duty DC motor and analog tachometer. Non-modular production models feature rubber bumpers, handles and a slotted rear guard. (1 per EA )

316 L Stainless Steel Large Flange Drive Adapter for use with High Speed Drive Adapter. For attachment of Overhead Drive Motors. Heavy duty cap assembly for large flange vessels Adapt overhead drives to teflon or sst folding impeller assembly 316 sst design with polyester stainless steel bearings (1 per EA )

Manufactured from Type 1 Class A Borosilicate Glass. Designed for culturing organisms that require a large surface area to volume ratio. Flask is supplied with a GL45 blue polypropylene linerless screw cap and pouring ring. Specifications: Type 1 Class A Borosilicate Glass Sizes: 2800ml OD X OAH (MM):210 X 225 Case Quantity: 1 (1 per EA )

Round Bottom Glass Pipette Canister. Manufactured From Type 1, Class A Borosilicate Glass Components Will Withstand Repeated Dry Or Steam Heat Sterilization Case Qty: 6 (6 per CS )

Type 1 class a Borosilicate glass ideal for freeze drying or cryogenic storage. Tubular firing off constriction on the neck. Rigidly controller bottom to withstand pressure at low temperature. Tubular round bottom Length:145mm Neck od: 8mm Capacity: 2ml (144 per CS )

Will not rust or deteriorate in water baths or co2 atmospheres. Manufactured from 303 stainless steel with electropolish finish. Each opening rack 1 1/16" (26.9mm) Tube size: 25mm Spacing: 6x12 holds 72 tubes Dimensions: 13 3/4" x 7" x 3 15/16" WIRE SPECIFICATIONS: SIDE & UPRIGHTS: .162"OD WIRE, CROSS WIRE: 0.063" OD WIRE, BTTM MESH: 1/4" Minimum order requirement: 5 each (1 per EA )

3000mL Bell-Flo™ Spinner Flask Flask Specifications: Material: Type 1 Class A Borosilicate Glass Dimensions: 165mm OD x 290mm Overall Height, 252.7mm across sidearms Two 45mm sidearms angled 53° off the centerline One 100mm Screw Thread Center Neck Indented Bottom: Prevents dead spot under impeller Side Baffles: Three equally spaced baffles, 100mm long x 9mm deep Supply with: Two 45mm PP Blue Screw Caps & PP Blue Pouring Rings (1 per EA )

Description: Glass Ball Impeller Assembly Only Size: 500mL Screw Cap: Blue PP, 100mm OD x 22.4mm T Cap Seal: Teflon, 95.3mm OD x 10.4mm T Sealing Ring: Blue silicone rubber, 91.4mm OD x 76.2mm ID x 6.1mm T Flex Tube: Soft silicone, 57.2mm OAL, 0.312” OD x 0.248” ID Magnet Tube: Type 1 Class A Borosilicate Glass, 110mm OAL, 28mm OD ball, houses one cast alnico magnet (1 per EA )

For use in the disinfectant testing procedure as described in aqac manual. Cylinder ends are lightly glazed. Hard surface carrier test for efficacy of testing of disinfectants. Sizes: 8x10mm (125 per CS )

Manufactured from type 1 class a Borosilicate glass. Ideal for growing, storing and mixing of aerobic and anaerobic cultures. Graduated to approximate volumes Size: 4l Closure: 38 Dimensions: 205x370mm (3 per CS )

Bellco manufactures all precision pipettes from type 1 class a Borosilicate glass. All bellco pipettes feature tempered tips and permanent silk screened graduations to withstand repeated usage and alkali washings. Constricted top for cotton plugging. (12 per CS )

LOW PROFILE CELL CULTURE VESSELS. REDUCED HEIGHT VESSELS MAXIMIZE INCUBATOR SPACE SUITABLE FOR ALL CELL CULTURE APPLICATIONS-INSECT, PLANT,BACTERIAL 100MM NECK FOR CAP ASSEMBLY AND OVERHEAD DRIVE 45MM VERTICAL SIDEARM ACCEPT PORT AND THERMOWELL ASSEMBLIES OR PROBES -SUPPLIED WITH 100MM CENTER CAP, 45MM CAPS AND POURING RINGS OD X OAH (MM): 240 X 295 Qty: 1 ea. (1 per EA )

SST Low Profile Impeller Assembly For 6000mL Low Profile Vessels. Requires Over Head Drive & cap assembly Material: SST 316l Consist of: dust shield, shaft, paddle, locking ring, washer, cotter pin Four (4) SST set screws: 8-32 x 1/4" Dimensions: 9 1/2" to 12 1/2" oal Paddle size: 3" tall x 5 1/4" wide Fully assembled (1 per EA )

Promotes optimal growth of suspension and micro-carrier culture. Impeller height adjust through compression fitting center cap. The indented bottom prevents accumulation of micro-carrier beads under impeller. Size: 15l Sidearm cap: 45mm Center cap: 100mm OD X OAH:294 X 470 (with cap) (1 per EA )

Flask only. For use circulating water bath or chiller and magnetic stir plate. Hose connection accepts 3/8" ID silicone tubing (Bellco M7965037) Available complete with micro-carrier impeller assembly or as components. Specifications: Jacket Volume (mL): 260ml Cap Size: 70mm Sidearm Cap Size (mm): 38 OD x OAH: 110x200mm (1 per EA )

The Bellco Process Controlled Bottom Drive Roller Apparatus holds up to 50 (see specifications below) full size glass or plastic roller bottles (110 to 120 mm diameter and up to 510 mm in length). The unit features a brushless DC motor and controller that operate at bottle speeds ranging from 0.3 to 9.0 rpm with the ability to select clockwise or counter clockwise direction. Units feature brushless, maintenance-free DC motors with drive assemblies designed for quiet operation. Four corner bumpers and two locking castors (on the front wheel positions) are also provided. Rollers are easily removed for replacement by using the special tool provided with each unit. All-Position Drive facilitates the use of lightweight plastic roller bottles by ensuring rotation at each bottle station, independent of any load configurations. (1 per EA )

The Bellco Digital Shaker is a compact, heavy-duty variable speed shaker. It is used for the agitation of electrophoretic gels and filter assay media for staining, destaining and assay development. The Shaker accommodates a variety of vessels. It is continuously adjustable from 30 to 350 RPM. This Bellco design incorporates an orbital platform that accepts a variety of optional trays. A variety of tray models are available, including three equipped with flask clamps for common sizes of flasks. Peg and Grommet style trays make changing convenient. The timer circuit permits automatic shutoff after 3-120 minutes. (1 per EA )

Polypropylene screw cap with silicone gasket pouring ring and compression fitting. 100mm (1 per EA )

Thermowell assemblies are used to hold inside one tube the rtd temperature sensor that monitors the temperature within the vessel in conjunction with a temperature controller. There are also tubes for addition of media and vent tube. • Thermowell assemblies for 1965 and 1967-style angled sidearm flasks, 3-port • 5/16" od thermowell tube,1/4" siphon and vent tubes • Includes 45mm pp cap and silicone gasket • Seam welded and electropolished • Longest tube length: 12 1/2" (1 per EA )

Bell-Flo iob assembly was designed to be used with the bell-flo vessel with bottom indents and 3 vertical baffles for optimal mixing. Rugged stainless steel ptfe internal bearing impeller assemblies utilize a wing style impeller blade that increases mixing. 1000mL Bell-Flo™ Internal Overhead Bearing Assembly Internal Overhead Bearing Assembly Specifications: Consists of screw cap, cap seal, sealing ring, compression washer, ball bearing spacer, ball bearing, bearing thimble, magnet, o-ring, magnet holder, shaft, & paddle 100mm PP Blue Screw Cap: 82.6mm OD x 22.4mm tall PTFE Cap Seal: 95.3mm OD x 25mm long Red Silicone Sealing Ring: 86mm OD x 76.2mm ID x 6.1mm thick White Silicone Compression Washer: 27.0mm OD x 12.7mm ID x 1.6mm thick PTFE Ball Bearing Spacer: 19.1mm OD x 12.7mm ID x 22.4mm deep PBT & SST Ball Bearing: 19.1mm OD x 6.4mm ID x 7.1mm deep PTFE Bearing Thimble: 31.8mm OD x 19.1mm ID x 38.1mm long PTFE Magnet: 9.5mm OD x 41.3mm long Silicone O-ring: 7.9mm OD x 4.8mm ID PTFE Magnet Holder: 19.1mm OD x 127mm long 316L SST Shaft: 6.4mm OD x 174.6mm long PTFE Paddle: 82.6mm wide x 127mm long x 1.6mm thick (1 per EA )

Manufactured from type 1 class a Borosilicate glass. Ideal for culture aerobic & anaerobic organisms, media storage and mixing. Deep skirted screw caps protect against contamination. Supplied with rubber line black phenolic caps and graduated to approximate volumes. Size: 500mL Cap: 38-415 Dimensions: 100x190mm (12 per CS )

SST Pitch Blade Assyembly. 316l stainless steel construction, electropolish finish For 10L Bioreactor Systems - English Threads Left hand - down OD: 3/1/4" Usually requires 2ea. (1 per EA )