Glassware

Bellco Roll-In Incubators have 40 cubic feet of volume and are designed for use with Bellco’s Cell Production Roller Apparatus (CPRA). The flush-to-floor design allows easy movement of the CPRA in and out of the chamber. Four internal convenience outlets allow simple connection to internally placed appliances such as CPRA, Roller Drums, Magnetic Stirrers, etc. Fans take air from the chamber top, pass it over the 1100 watt heater and re-inject it into the chamber on the bottom back wall. A microprocessor temperature controller and membrane keypad allows simple setting and monitoring of chamber temperature. A safety thermostat is included to prevent over-temperature failures. Shelf brackets are included for mounting of optional shelves. The control panel features indicating lights and dials for automatic control of temperature. (1 per EA )

The Bellco Auto-blot Mini Hybridization Oven consists of an incubator with an integral rotisserie device. The rotisserie has the capacity for up to 4 large hybridization bottles or 8 small hybridization bottles. Alternatively, any combination of large or small bottles can be used. This Auto-blot Micro Hybridization Oven features an advanced temperature controller for precise control of oven temperature. 14”x17”x13” (35x42x32cm) Int: 7”x15”x8” (18x37x20cm) 115v. (1 per EA )

Manufactured from Type1 Class B Borosilicate Glass. Large opening and sloping shoulders facilitate pouring and cleaning. Heavier walls prevent breakage of glass. Media storage bottles have white graduations and a marking area. They are supplied with rubber lined black phenolic screw cap. Specifications: Type 1 Class B Borosilicate Glass Sizes: 250ml (33)mm Cap OD x OAH: 66 x 149 Case Quantity: 12 (12 per CS )

The Bellco 100 mm Overhead Drive Cap Assembly is manufactured from 316L SST with dual bearings and seals. A dust shield for paddle assemblies (1/4” shaft) is included. Cap assembly features two 1/4” NPT female ports for addition of optional fittings. (1 per EA )

SST Pitched Blade Impeller Material: 316l SST with electropolish finish English thread OD: 1 3/4" For 5/16" od shafts Usually requires 2 each (1 per EA )

Manufactured from type 1 class a Borosilicate glass. Includes 6 45mm polypropylene blue screw caps and pouring rings, also 1 100mm polypropylene blue cap for the center. Suitable for all cell culture fermentation. Compatible with bellco over head drive and magnetic stirrers. Specifications: Material: Type 1 Class A Borosilicate Glass 100mm Center Neck Baffles: 0 Sidearms: 6 OD x OAH: 410 x 535mm (1 per EA )

These stainless steel port assemblies are designed for use with media storage bottles for adding and withdrawing media or liquids. The 2- port models feature a siphon vent tube and is supplied with a 45mm polypropylene blue open top screw cap and white silocone liner. DESIGNED FOR 5637 AND 5639 MEDIA STORAGRE BOTTLES. -WELDED, 316L STAINLESS STEEL CONSTRUCTION, 1/4" INCH OD TUBING. -ELECTROPOLISHED FINISH, CONTINUOUS SEAL WELD. -TWO PORT MODEL FEATURES SIPHON AND VENT TUBES. -LONG TUBE: 8 1/2" (1 per EA )

Flask Only. For use circulating water bath or chiller and magnetic stir plate. Hose connection accepts 3/8" ID silicone tubing (Bellco M7965037) Available complete with micro-carrier impeller assembly or as components. Specifications: Jacket Volume (mL): 40ml Cap Size: 51mm Sidearm Cap Size (mm): 18 OD x OAH: 70x120mm (1 per EA )

Description: Glass Ball Spinner Comp, 1000mL Size: 1000mL Material: Type 1 Class A Borosilicate Glass Flask Dimensions: 135mm OD x 240mm OAH, two 45mm sidearms offset at 60º, 100mm center neck Includes two 45mm blue PP screw caps & two 45mm blue PP pouring rings Impeller Assembly: one 100mm blue PP screw cap, 100mm Teflon cap seal, 100mm blue silicone sealing gasket, soft silicone flex tube, glass ball magnet tube, and magnet Specially Formed Bottom Indent Prevents Accumulation under impeller Glass ball houses a magnet for gentle agitation of Micro carrier Beads (1 per EA )

Manufactured from 316l stainless steel for standard bioreactor vessels. Use with over head drive motors. PADDLE L X W (IN): 3 X 14. (1 per EA )

Manufactured from type 1 class a Borosilicate glass. Bottom pad prevents chipping and breaking of pipette tips. All components can and will withstand repeated dry or steam heat serialization. Supplied stainless steel closure. Case qty-6 (6 per CS )

Low profile 45mm 2-port assembly for vertical low profile 3L vessels Seamed welded – electropolish 316l stainless steel material 32ra finish or better All tubes; .250"od x .152"id Siphon tube (LONG TUBE); 8 1/2" LONG. VENT TUBE: 1". SUPPLY WITH S/CAP (A523-599) & WHITE SILICONE LINER (A523-600) (1 per EA )

Headplate setup stand is for hands-free assembly of bioreactor head plates manufactured from aluminum and measures 8"x8"x3" assembled. Headplate is inserted into the slot on the stand and secured into place with thumbscrews. It holds any head plate up to 6mm thick. (1 per EA )

Stainless steel shaft design prevents cell damage and minimizes magnetic decoupling. Sealed internal assembly requires less incubator space. For use with bellco 1965-series standard and water jacketed spinner flasks. Cap size: 100mm Flask size: 15 PADDLE; L X W:9.5 X 6 IN (1 per EA )

The Bellco Refrigerated Roll-In Incubators have 40 cubic feet of volume and are designed for use with Bellco’s Cell Production Roller Apparatus (CPRA). The flush-to-floor design allows easy movement of the CPRA in and out of the chamber. Four internal convenience outlets allow simple connection for internally placed appliances such as CPRA, Roller Drums, Magnetic Stirrers, etc. Shelf brackets are included for mounting optional shelves to hold these appliances. Fans take air from the chamber top, pass it over the 1100 watt heater and inject it into the chamber on the bottom back wall. When the refrigeration mode is active, the air is cooled using a thermoelectric cooler. A microprocessor temperature controller and membrane keypad allows simple setting and monitoring of chamber temperature. The control panel contains indicator lights and dials for controlling temperature. A safety thermostat is included to prevent over-temperature failures. The unit is not intended for use with CO2 environments. (1 per EA )

Bell-ennium Magnetic Stirrers are designed for both cell cultures in spinner flasks as well as for general laboratory procedures requiring the use of magnetic stirring equipment. Bell-ennium stirrers offer the laboratory researcher a wide range of capabilities and the latest innovations in stirring technology. Bell-ennium stirrers feature brushless maintenance free DC motors with drive assemblies designed for quiet operation. Stainless steel covers are stamped to show the vessel positions for accurate placement and optimum performance. The Bell-ennium single position low profile chassis measure 10 x 11 x 3 3/8” and are designed to fit side-by-side in Bellco incubators. Units are powered by standard 24V in-line power supplies and are CE compliant. (1 per EA )

Manufactured from Type 1 Class A Borosilicate Glass with a low coefficient of expansion. Heavy wall beakers meet astime-960 type 1 specifications for classification design capacity and markings. Features a easy pour spout, white permanent graduations and a large marking square. Specifications: Type 1 Class A Borosilicate Glass Size: 4L Dimensions: 160 x 250mm Case Quantity: 3 (2 per CS )

Will not rust or deteriorate in water baths or co2 atmospheres. Manufactured from 303 stainless steel with electropolish finish. Each opening rack 1 9/16" (39.6mm) Tube size: 38mm Spacing: 2x6 holds 12 tubes Dimensions: 10" x 3 1/2" x 2 7/8" WIRE SPECIFICATIONS: SIDE & UPRIGHTS: .162"OD WIRE, CROSS WIRE: 0.063" OD WIRE, BTTM MESH: 1/4" Minimum order requirement: 5 each (1 per EA )

The Bellco Auto-blot Micro Hybridization Oven consists of an incubator with an integral rotisserie device. The rotisserie has the capacity for up to 4 large hybridization bottles or 8 small hybridization bottles. Alternatively, any combination of large or small bottles can be used. This Auto-blot Micro Hybridization Oven features an advanced temperature controller for precise control of oven temperature. Without Rotisserie 14”x17”x13” (35x42x32cm) Int: 7”x15”x8” (18x37x20cm) 115v. (1 per EA )

Manufactured from Type 1 Class A Borosilicate Glass with a low coefficient of expansion. Heavy wall beakers meet astime-960 type 1 specifications for classification design capacity and markings. Features a easy pour spout, white permanent graduations and a large marking square. Specifications: Type 1 Class A Borosilicate Glass Size: 400mL Dimensions: 80 x 106mm Case Quantity: 12 (12 per CS )

The Bellco Auto-blot Micro Hybridization Oven consists of an incubator with an integral rotisserie device. The rotisserie has the capacity for up to 4 large hybridization bottles or 8 small hybridization bottles. Alternatively, any combination of large or small bottles can be used. This Auto-blot Micro Hybridization Oven features an advanced temperature controller for precise control of oven temperature. Ext: 14”x17”x13” (35x42x32cm) 230v (1 per EA )

316-l stainless steel ra32 or better finish .040" drilled holes sparger for low profile vertical side arm vessels. Threaded end is removable for cleaning. Comes with 45mm blue polypropylene open top cap and silicone gasket. Triple tube configuration With Vent, Fill/Sample And Sparge. (1 per EA )

Bell-ennium Process Magnetic Stirrers are designed for both cell cultures in spinner flasks as well as for general laboratory procedures requiring the use of magnetic stirring equipment. The Front-End models are designed to position so that one flask is positioned behind the other, minimizing the width of the stirrer for limited space work areas. Bell-ennium stirrers feature brushless maintenance free DC motors with drive assemblies designed for quiet operation. Stainless steel covers are stamped to show the vessel positions for accurate placement and optimum performance. Heavy duty magnet assemblies provide the best magnetic coupling while timing belts on all positions insure smooth even stirring of vessel contents. The low profile chassis measure 11 x 20 x 3 3/8” and are designed to fit side-by-side in Bellco incubators. The PID process controller provides RS-485 communication with your existing lab network (software not included), as well as two alarm outputs for the optional Motion Alarm. Units are powered by standard 24V in-line power supplies and are CE compliant. (1 per EA )

Bell-ennium Magnetic Stirrers are designed for both cell cultures in spinner flasks as well as for general laboratory procedures requiring the use of magnetic stirring equipment. Bell-ennium stirrers offer the laboratory researcher a wide range of capabilities and the latest innovations in stirring technology. Bell-ennium stirrers feature brushless maintenance free DC motors with drive assemblies designed for quiet operation. Stainless steel covers are stamped to show the vessel positions for accurate placement and optimum performance. The Bell-ennium single position low profile chassis measure 10 x 11 x 3 3/8” and are designed to fit side-by-side in Bellco incubators. Units are powered by standard 24V in-line power supplies and are CE compliant. (1 per EA )