Glassware

Stainless steel 3L low profile impeller assembly For low profile Over Head Drive vessel Material: SST 316L Electropolish finish, ra 32 or better Fully assembled Paddle dimensions: 2" T X 5 1/4" W (1 per EA )

Bell-ennium Process Magnetic Stirrers are designed for both cell cultures in spinner flasks as well as for general laboratory procedures requiring the use of magnetic stirring equipment. The Front-End models are designed to position so that one flask is positioned behind the other, minimizing the width of the stirrer for limited space work areas. Bell-ennium stirrers feature brushless maintenance free DC motors with drive assemblies designed for quiet operation. Stainless steel covers are stamped to show the vessel positions for accurate placement and optimum performance. Heavy duty magnet assemblies provide the best magnetic coupling while timing belts on all positions insure smooth even stirring of vessel contents. The low profile chassis measure 11 x 20 x 3 3/8” and are designed to fit side-by-side in Bellco incubators. The PID process controller provides RS-485 communication with your existing lab network (software not included), as well as two alarm outputs for the optional Motion Alarm. Units are powered by standard 24V in-line power supplies and are CE compliant. (1 per EA )

The Bellco Digital Mini-Orbital Shaker is a high speed shaker for general laboratory cell culture experimentation. This Bellco design incorporates an orbital platform that accepts a variety of optional trays. Peg and grommet design offers a simple method to install or change trays; four versions of trays are available. Brushless DC motor designed for minimal maintenance. (1 per EA )

Bellco Roll-In Incubators have 40 cubic feet of volume and are designed for use with Bellco’s Cell Production Roller Apparatus (CPRA). The flush-to-floor design allows easy movement of the CPRA in and out of the chamber. Four internal convenience outlets allow simple connection to internally placed appliances such as CPRA, Roller Drums, Magnetic Stirrers, etc. Fans take air from the chamber top, pass it over the 1100 watt heater and re-inject it into the chamber on the bottom back wall. A microprocessor temperature controller and membrane keypad allows simple setting and monitoring of chamber temperature. A safety thermostat is included to prevent over-temperature failures. Shelf brackets are included for mounting of optional shelves. The control panel features indicating lights and dials for automatic control of temperature. (1 per EA )

Type 1 class a Borosilicate glass for freeze drying or cryogenic storage. The neck has pre-drawn constriction to facilitate sealing. Flat bottom Constriction neck Neck od : 8mm Bottom od: 11mm Capacity: 1ml Length: 145mm (144 per CS )

Heavy gauge rectangular construction for easy stacking and storage. These pipette cans can be sterilized by autoclave or dry heat. (do not exceed 400 degrees F). Includes silicone pad on the inside of top and bottom to protect pipette tips. --Satin finish surface of entire can for convenient marking or coding. --Silicone pads on inside of top and bottom protect pipette tips. --Material: 304 stainless steel .031” thick (1 per EA )

For use circulating water bath or chiller and magnetic stir plate. Hose connection accepts 3/8" ID silicone tubing (Bellco M7965037) Available complete with micro-carrier impeller assembly or as components. Specifications: Jacket Volume (mL): 1300ml Cap Size: 100mm Sidearm Cap Size (mm): 45 OD x OAH: 200x330mm (1 per EA )

Bellco Magnetic Stirrers are specifically designed for growing both mammalian and bacterial cultures where minimal heat transfer from the magnetic stirrer to the culture vessel is essential. They are ideal for tissue cultures grown in spinner flasks. Bellco incorporates low wattage DC motors to reduce stirrer heat up. Independent power and speed controls allow unit to maintain a speed setting when switched on and off. Powerful magnets rotate on ball bearing shafts for increased coupling and continuous maintenance free service. Polyurethane drive belts resist humidity and temperature. The 100V, 115V & 230V models feature a convenience outlet that allows daisy chaining of up to ten stirrers. Speed range: 30 - 1000 rpm +/- 5% (1 per EA )

Low Profile Glass Impeller Assembly Size: 3000ml (for low profile 3l vessel) Paddle: 3" tall x 7" wide (1 per EA )

Ideal for florescence and con-focal microscopy Size: 25mm round od Material: German glass ( d-263m) 200 areas in diamond pattern Each square measures 0.6mm x 0.6mm Facilitates mounting of micro-manipulated cells or chromosome spreads Line thickness: .02mm (25 per CS )

SST Sample Port Assyembly for 7l bioreactor systems - English threads Material: 316l SST with electropolish finish - inside & out Tubing specifications: .250" od x .152" id Overall length: 14 5/16" Insertion length: 12 7/8" Supply with SST 3/8-24 nut & o-ring (1 per EA )

Leighton culture tubes are useful for the study of pathogenic effects on viruses on cells as well as sponge matrix culture and nutritional studies. Use cover slips for preparing expectant tissue cultures with leighton culture tubes. White marking area (36 per CS )

Heavy gauge rectangular construction for easy stacking and storage. These pipette cans can be sterilized by autoclave or dry heat. (do not exceed 400 degrees F). Includes silicone pad on the inside of top and bottom to protect pipette tips. --Satin finish surface of entire can for convenient marking or coding. --Silicone pads on inside of top and bottom protect pipette tips. --Material: 304 stainless steel .031” thick (1 per EA )

Hi-torq SST OHD impeller assembly, full width Size: 15l For hi-torq motor & cap assembly (7774-40115/40230/ & 7764-74000) Similar to 1964-60015 but to accept 1/2" shaft from 7764-74000 cap assembly Material: 316l Paddle size: 3" tall x 9" wide (1 per EA )

Ideal use for over head drive vessels. 15L OHD Impeller Assembly Consists of Paddle, Plug, Paddle Holder, and Drive Shaft Paddle [A523-214]: PTFE material, 171.5mm wide x 76.2mm tall x 1.6mm thick Plug [A542-49]: PTFE, 9.5mm OD x 19.1mm long (approx.) Paddle Holder [A542-50]: White PTFE, 279.4mm long x 19.1mm OD Drive Shaft [A542-47]: 316L SST, 215.9mm long x 6.4mm OD (approx.) (1 per EA )

The Bellco Sci-ERA Dual Pan Hot Shaker is a slow speed, large orbit shaker with two independently controlled baths for incubation of electrophoretic gels and filter hybridization media. Stringent temperature control with a sensitivity of +/-0.1oC is useful for many biochemical assays. This Bellco design incorporates a seamless stainless steel lined temperature controlled water bath mounted on a low-profile one inch orbiting platform. The unique chamber design offers simple containment of potential spills. The chamber is completely isolated from electromechanical components. The Sci-ERA Dual Pan Hot Shaker has audible over-temperature alarms and built-in safety features to prevent heater burn-out. An easy-to-use microprocessor controller offers stringent temperature control. (1 per EA )

The Bellco Pipette Plugger is designed for plugging a full range of standardized cotton plugging pipettes. This unit has three speeds and can be adjusted quickly and easily to plug 40, 50 or 60 pipettes per minute. The unit will produce uniform shape cotton plugs, minimizing the problem of tight and loose plugs. Machine is portable with a convenient carrying handle. Time tested design with a precision Geneva mechanism. --Speed Range: 3 Settings, Approximately 40/50/60 Pipettes/Minute --Weight: 19 Lbs. (9.0 Kg) --Operates In: Continuous Or Actuate Mode --Supplied With 1 Bag Of Cotton Roving 7750-22222 (1 per EA )

Ideal for use with water baths for precise temperature control. Water jacketed low profile OHD vessel with: size: 3l four (4) vertical 45mm sidearms dimensions: 300mm od x 280mm overall height two (2) #4 hose connections material: type 1 class a borosilicate glass supply: 100mm pp blue cap & white silicone liner & four 45mm pp blue caps & pouring rings (1 per EA )

Size: 6l Seam welded w/ electropolish finish 3-port w/ siphon, fill & vent tubes Includes: 45mm pp cap & silicone gasket Dimensions: 1/4" OD x .152" ID Longest tube: 10 1/2" at curve (1 per EA )

These stainless steel port assemblies are designed for use with media storage bottles for adding and withdrawing media or liquids. The 2- port models feature a siphon vent tube and is supplied with a 45mm polypropylene blue open top screw cap and white silocone liner. DESIGNED FOR 5637 AND 5639 MEDIA STORAGRE BOTTLES. -WELDED, 316L STAINLESS STEEL CONSTRUCTION, 1/4" INCH OD TUBING. -ELECTROPOLISHED FINISH, CONTINUOUS SEAL WELD. -TWO PORT MODEL FEATURES SIPHON AND VENT TUBES. -LONG TUBE: 10" (1 per EA )

Used to generate a localized cold surface on the exterior of the finger. Commonly used for sublimation, and can also be used in re-flux or distillation operations. 7L. (1 per EA )

2-port 45mm cap assembly, 8l For 8l 1964 style Over Head Drive vessels Long tube: 1/4"od x 16 1/4" Short tube: 1/4"od x 2.5/32" All tubes extended up 1.0" above the cap slug Supply 45mm s/cap & white silicone liner (1 per EA )

Thermowell assembly is manufactured from 316l stainless steel with 32ra finish or better. It can be used with rtd temperature sensor. Includes polypropylene screw cap and silicone gasket. There are also tubes for addition media and vent. Thermowell assemblies attach to the sidearms with a screw cap assembly. Specifications: Material: 316L Stainless Steel 32Ra Finish or Better Includes: Screw Cap & Silicone Gasket (1 per EA )

Flat Bottom Glass Pipette Canister W/Silicone Pad, Manufactured From Borosilicate Glass. All Components Will Withstand Repeated Dry Or Steam Heat Sterilization Bottom Pad Prevents Chipping Of Pipette Tips. Case Qty: 6 (6 per CS )