Glassware

Adapter Multiple - Three necks, Socket 19/26, Cone 29/32 (1 per EA )

Bulb Pipette, USP BBR AS 9 mL, one-mark, pk of 6 (6 per PK)

Pipette, Serological, Globe Glass, Reusable, 0.1mL, To Deliver (TD), 0.01 Graduations, White Band, ASTM E1044 (12 per CS)

Pipette, Serological, Globe Glass, Reusable, 1mL, To Deliver (TD), 0.1 Graduations, Red Band, ASTM E1044 (12 per CS)

Stainless Steel Hi-Torq Over Head Drive Impeller Full Width 8L Specifications: Hi-Torq SST Over Head Drive Impeller Assembly – Full Width Size: 8L . For Hi-Torq Motor & Cap Assembly (7774-40115/40230 & 7764-74000) Similar To 1964-60008 But To Accept 1/2" Shaft From 7764-74000 Cap Assembly Material: 316L SST With Elelctropolish Finish Ra32 Or Better Paddle Size: 3" Tall X 8" Wide (1 per EA )

The stainless steel 100mm IOB probe cap seal is manufactured from 316L stainless steel and has a red-silicone sealing gasket with a 100mm blue polypropylene screw cap. The stainless steel probe cap seal has four accessory ports surrounding a centrally located internal impeller assembly. Two of these ports have a white silicone plug inside a threaded cap that acts as a compression fitting for probe insertion. The other ports accept accessories using the same silicone compression plugs and threaded caps. These compression plugs make it easy to adjust the insertion length of probes or straight tubes depending upon the working volume of the bioreactor flask. The stainless steel cap seal, stainless steel PTFE impeller and all fittings are steam autoclavable. (1 per EA )

The Bellco Auto-blot Mini Hybridization Oven consists of an incubator with an integral rotisserie device. The rotisserie has the capacity for up to 4 large hybridization bottles or 8 small hybridization bottles. Alternatively, any combination of large or small bottles can be used. This Auto-blot Micro Hybridization Oven features an advanced temperature controller for precise control of oven temperature. 14”x17”x13” (35x42x32cm) 230v (1 per EA )

Description: Glass Ball Spinner Flask Only Size: 250mL Material: Type 1 Class A Borosilicate Glass Dimensions: 85mm OD x 140mm Overall Height, 164mm across sidearms Two 32mm Sidearms angled 55° offset center 70mm Screw Thread Center Neck Dimpled Bottom Graduations: 50mL to 250mL, every 25mL – White Ink (Approx Volumes) Supply with: Two 32mm PP Blue Screw Caps & PP Blue Pouring Rings (1 per EA )

Manufactured from type 1 class a Borosilicate glass. Designed with deep side baffles for optimal agitation. Large bottom surface for easy access with Bellco large orifice pipette. Break resistant lip Size: 125mL OD x OAH – 66 x 115mm 3 per case (3 per CS )

400mm Graham condenser is designed for use in distillation applications. Constructed of borosilicate glass, this condenser has a coiled inner tube to provide additional surface area for highly efficient cooling. Socket is 24/40 with a screw thread connector. (1 per EA)

Pack of 10 plastic, conical joint clamps (also known as keck clamps), designed to securely fasten together glassware with a 24/40 joint size. Ideal for lab setups including condensation and distillation. (10 per PK )

Mohr Measuring Pipets, 5 mL, 0.1 graduation interval (12 per PK )

45mm low profile Thermowell assembly for low profile 3l vessel. Seam welded - electropolish finish 316l stainless steel material ra 32 finish or better Supply with s/cap (a523-599) & white silicone liner (a523-600) 1 - THERMOWELL TUBE: 5/16"OD X .242"ID X 1.0" above x 8 11/32" insertion 1- FILL TUBE: 1/4"OD X .152"ID X 1.0" above x 8 11/32" insertion 1- VENT TUBE: .250"OD X .152"ID X 1.0"LONG (1 per EA )

Probe adapters & compression fittings. Bellco compression fittings are designed using our standard 45 mm blue polypropylene open top caps and white silicone gaskets. A wide variety of fittings are available to allow pH and do monitoring via insertion of these probes into the sidearms of vessels. Bellco probe adapters are designed to allow introduction of threaded probes into vessels through 200 mm stainless steel headplate or a 45 mm vertical sidearm. Probe OD: 1/2" Stainless steel fitting w/ cap ½" (1 per EA )

United Scientific® Pipettes, Volumetric, Class A, Individually Certified, 0.5 mL (5 per PK )

200mm Vigreux column with 24/40 joint. A Vigreux column is a type of air condenser where the simple tube has been modified to include an abundance of downward-pointing indentations. This dramatically increases the surface area per unit length of the condenser. (1 per EA)

500mm Vigreux column with 24/40 joint. A Vigreux column is a type of air condenser where the simple tube has been modified to include an abundance of downward-pointing indentations. This dramatically increases the surface area per unit length of the condenser. (1 per EA)

500mm Graham condenser is designed for use in distillation applications. Constructed of borosilicate glass, this condenser has a coiled inner tube to provide additional surface area for highly efficient cooling. Socket is 24/40 with a screw thread connector. (1 per EA)

The Lead Rings are perfect for stabilizing vessels and labware or for water bath immersions. (1 per EA)

Test Tube, light wall rimless, 15ml, 125x16mm, Borosilicate glass, PK/48 (48 per PK )

Serological Pipets, 2 mL, 0.1 graduation interval (12 per PK )

These pipettes are made from borosilicate glass in compliance with ASTM specification E-1293. Color-coded. Batch certified. Calibrated to deliver. Printed with durable amber markings. (5 per PK )

These pipettes are made from borosilicate glass in compliance with ASTM specification E-969. Color-coded. Individually serialized and certified. Calibrated to deliver. Printed with durable amber markings. (5 per PK )

For use circulating water bath or chiller and magnetic stir plate. Hose connection accepts 3/8" ID silicone tubing (Bellco M7965037) Available complete with micro-carrier impeller assembly or as components. Specifications: Jacket Volume (mL): 75ml Cap Size: 70mm Sidearm Cap Size (mm): 18 OD x OAH: 75x160mm (1 per EA )