Containers

Manufactured from type 1 class a Borosilicate glass. Designed for the measurement of microbial co2 production over time. Ideal for bio-remediation studies. All components are autoclaveable. Complete 250mL, 1 each. (1 per EA )

This Bellco CO2 Incubator has 28 cubic feet of volume and is designed for use with Bellco’s Cell Production Roller Apparatus. Multiple internal convenience outlets allow simple connection to internally placed appliances such as CPRA, Roller Drums, Magnetic Stirrers, etc. A fan takes air from the chamber top, passes it over a 1100 watt heater and re-injects it into the chamber on the back wall. A touchscreen temperature and CO2 controller allows simple setting and monitoring of chamber temperature. A safety thermostat is included to prevent over-temperature failures. Shelf brackets are included for mounting of optional shelves. (1 per EA )

Will not rust or deteriorate in water baths or co2 atmospheres. Manufactured from 303 stainless steel with electropolish finish. Each opening rack 1 1/16" (26.9mm) Tube size: 25mm Spacing:4x10 holds 40 tubes Dimensions: 11 1/2" x 4 3/4" x 4" WIRE SPECIFICATIONS: SIDE & UPRIGHTS: .162"OD WIRE, CROSS WIRE: 0.063" OD WIRE, BTTM MESH: 1/4" Minimum order requirement: 5 each (1 per EA )

4" od 316l stainless steel, ra32 finish or better Marine impeller with 1/2" bore & set screw. (1 per EA )

Glass shaft impeller assembly for 1967-style hanging bar spinner flask. Consist of ptfe magnet holder and ptfe coated magnet. Glass shaft ptfe magnet Size: 50-500ml CONSIST OF: PTFE MAGNET HOLDER and PTFE COATED MAGNET (1 per EA )

Ideal use for Biometer flask. Consist of: needle and stopper Packed 1 per case (1 per EA )

MICROCARRIER SPINNER FLASKS -PROMOTES OPTIMAL GROWTH OF SUSPENSION AND MICROCARRIER CULTURE -IMPELLER HEIGHT ADJUSTS THROUGH COMPRESSION FITTING -INDENTED BOTTOM (UP TO 1L) PREVENTS ACCUMULATION OF MICROCARRIER BEADS UNDER IMPELLER OD X OAH:410 X 545 (with cap) CAP:100MM SIDEARM:45MM (1 per EA )

Stainless Steel Shaft Assembly The Bellco Stainless Steel Shaft Conversion Kit is designed to convert your standard glass shaft to stainless steel on 1967 and 1965 Spinner Flasks. Sizes range from 100 mL to 36 liters for 1965 spinners and 100 to 3000 mL for 1967 spinner flasks. Material: 316L Stainless Steel and polypropylene compression fitting. Size: 250ml (1 per EA )

Manufactured from Type 1 Class A Borosilicate Glass. Shake flasks are the basic tool for growth studies of aerobic microbial cultures. They have rigidly controlled baffle angles and depths to promote optimal oxygen transfer while reducing vortex formation. Designed for all orbital shakers. Specifications: Type 1 Class A Borosilicate Glass Sizes: 500mL Closure Sizes: 38mm OD x OAH: 100 x 205mm DeLong Style Neck Case Quantity: 2543-00500: 12 (12 per CS )

• Material: Type 1 Class A Borosilicate Glass • Dimensions: 63.5mm OD x 135mm Overall Height • Graduations: 20mL – 100mL, every 20mL • Bottom indents and three vertical baffles for optimal mixing • Two 32mm Side arms angled 45° off center for Port Assemblies • One 70mm Screw Thread Center Neck • Rugged stainless steel/ PTFE Internal Bearing Assembly • Supply with: Two 32mm PP Blue Screw Caps (1 per EA )

Type 1 class a Borosilicate glass for freeze drying or cryogenic storage. The neck has pre-drawn constriction to facilitate sealing. Flat bottom Constriction neck Neck od: 9mm Bottom od: 12mm Capacity: 2ml Length: 145mm (144 per CS )

Type 1 Class A Borosilicate Glass 19L #12 Stopper Neck 292mm OD x 485mm OAH (1 per EA )

Manufactured from Type 1 Class A Borosilicate Glass. Ideal for use of filling other glass vessels. Receiving vessel is placed under bell to maintain aseptic conditions during filling. Attaches to reservoir with rubber tubing. Specifications: Type 1 Class A Borosilicate Glass Dimensions: 41x95mm Tubing Size: 1/4" 2 per case (2 per CS )

Used to surround a single cell to create homogeneous culture of cells rather than mixed population. The flat end ensures tight sealing with surface of culture dish. Sizes: 6x8mm (125 per CS )

Manufactured from type 1 class a Borosilicate glass. Ideal for culture aerobic & anaerobic organisms, media storage and mixing. Deep skirted screw caps protect against contamination. Supplied with rubber line black phenolic caps and graduated to approximate volumes. Size: 25mL Cap: 18-415 Dimensions: 41x65mm (24 per CS )

Manufactured from type 1 class a Borosilicate glass. Ideal for culture aerobic & anaerobic organisms, media storage and mixing. Deep skirted screw caps protect against contamination. Supplied with rubber line black phenolic caps and graduated to approximate volumes. Size: 6L Cap: 38-415 Dimensions: 235x390mm (3 per CS )

Type 1 Class A Borosilicate Glass ideal for freeze drying or cryogenic storage. Tubular firing off constriction on the neck. Rigidly controller bottom to withstand pressure at low temperature. Tubular round bottom Length: 170mm Neck od: 8mm Capacity: 4ml (144 per CS )

Approx 25 x 34" (63.5 x 86.5cm). Stainless steel mesh with reinforcing bars. Fits on adjustable clips inside incubator. Load: 240 lbs (max). (1 per EA )

Used to surround a single cell to create homogeneous culture of cells rather than mixed population. The flat end ensures tight sealing with surface of culture dish. Sizes: 8x8mm (125 per CS )

Type 1 class a Borosilicate glass ideal for freeze drying or cryogenic storage. Tubular firing off constriction on the neck. Rigidly controller bottom to withstand pressure at low temperature. Tubular round bottom Length: 145mm Neck od: 8mm Capacity: 3ml (144 per CS )

Description: Bio-Probe Spinner Flask Complete Bio-Probe Spinner Flask Complete consists of: Flask, and Impeller Assembly. Flask Specifications: Material: Type 1 Class A Borosilicate Glass Dimensions: 136mm OD x 240mm Overall Height Two 45mm Side arms angled 60° off center Two 32mm Side arms angled 35° off center One 100mm Screw Thread Center Neck Indented bottom Graduations: 200mL to 1000mL, every 100mL – White Ink (Approx Volumes) Supply with: Two 45mm PP Blue Screw Caps, two PP Blue Pouring Rings, two 32mm blue screw caps, and two o-rings Impeller Assembly Specifications: Impeller Assembly consists of paddle, shaft, O-ring, retaining ring, magnet, magnet holder, adjustable paddle, bearing thimble, bearing spacer, ball bearing, compression spacer, compression washer, sealing ring, cap seal, and screw cap. Adjustable from 220mm-227mm in height. Paddle: PTFE , 4 1/4”x3”x1/16” Shaft: 316L Stainless Steel, 8 7/16” long x ¼” OD O-ring: Silicone, -008 Retaining ring: 316L SST, 0.365” OD x 17/64” ID x 5/32” long Magnet: PTFE coated, ½” OD x 3” long Magnet holder: PTFE, ¾” OD x ¼” ID x 4 11/16” long Adjustable paddle: PTFE, 3 3/8”x 1 ½” with a hub OD of 1 ½” Bearing thimble: PTFE, 1 ¼” OD by 4/4” ID x 3 1/8” long Bearing spacer: PTFE, ¾” OD x ½” ID x 0.880” long Ball bearing: Polybutylene terephthalate & SST, ¾” OD x ¼” ID x 0.281 thick Compression spacer: PTFE, ¾” OD x ½” ID x 1.645” long Compression washer: White Silicone, 1 1/16” OD x ½” ID x 1/16” thick Sealing ring: Red silicone, 3.6” OD x 3” ID x 0.240” thick Cap seal: PTFE, 3 ¾” OD x 0.985” long Screw cap: Blue Polypropylene, 4.25” OD x 7/8” long (1 per EA )

Manufactured from type 1 class a Borosilicate glass. Ideal for all cell culture and media storage purposes. Provides flexible secure seal without a liner. Supplied with gl45 liner-less screw cap and pouring rings. Graduated to approximate volumes. Size: 6L Dimensions: 235x370mm (1 per EA )

Blades and impeller assemblies are use for cell culture. Reduces shear in delicate cell culture. Manufactured from 316l stainless steel with electropolish finish. Ra 32 finish or better inside and out. Blade dimension: 5 3/4 x 2". Shaft oal: 17". MARINE IMPELLER INCLUDES 1/2" SHAFT AND IMPELLER BLADE OMNI AND Z-Z PADDLES ARE ONE PIECE WELDED, 1/4" SHAFT (1 per EA )

Ideal for growing, storing and mixing or aerobic and anaerobic cultures. The 3 bottom baffles increase culture oxygenation. Includes 25mm Bellco stainless steel closure (2005 series) Specifications: Type 1 Class A Borosilicate Glass Sizes: 300ml Includes: Bellco Stainless Steel Closure (2005 Series) Sidearm Dimensions: 12x130mm Case Quantity: 4 (4 per CS )