Desiccators

VDR-30G Vacuum Desiccator with Gauge, 9.5lbs/ Dia. 16.8 x 18.7, 20L (0.7cu ft) (1 per EA )

These autoclavable desiccators are made of polypropylene (PP) and polycarbonate. Autoclavable at 120°C for 15 minutes. The top dome, molded in rigid and transparent PC, gives a crystal-clear view of the sample. The knurled knob on the top provides easy handling of the dome. The lower part is made of PP. An internal groove on the flange holds the silicon rubber O-ring. Vacuum grease should be applied on the flanges to make it air-tight. (1 per EA)

These autoclavable desiccators are made of polypropylene (PP) and polycarbonate. Autoclavable at 120°C for 15 minutes. The top dome, molded in rigid and transparent PC, gives a crystal-clear view of the sample. The knurled knob on the top provides easy handling of the dome. The lower part is made of PP. An internal groove on the flange holds the silicon rubber O-ring. Vacuum grease should be applied on the flanges to make it air-tight. (1 per EA)

VDR-20G Vacuum Desiccator with Gauge, 3.7lbs/ Dia.11.3 x 13.9, 6L (0.2cu ft) (1 per EA )

These autoclavable desiccators are made of polypropylene (PP) and polycarbonate (PC) and can hold a vacuum up to 740mm Hg for 24 hours without any greasing. Autoclavable at 121°C for 15 minutes. The top dome, molded in rigid and transparent PC, gives a crystal-clear view of the sample. The knurled knob on the top provides easy handling of the dome. The lower part is made of PP and includes a perforated PP desiccator plate. An internal groove on the flange holds the silicon rubber O-ring. The PP stopcock accepts 1/4" I.D. tubing and has a self-lubricating PTFE plug. Use the three-way plug to create a vacuum, release a vacuum, or for shut-off. (1 per EA)

Non-vacuum desiccator manufactured from clear borosilicate glass, including borosilicate glass lid with a molded-in knob. Also includes a perforated porcelain desiccator plate that fits onto a ridge above the lower chamber. A standard drying agent, such as silica or anhydrous calcium chloride, can be positioned in the lower chamber. Autoclavable. Flange outer diameter: 200mm Flange inner diameter: 180mm Top chamber diameter: 200mm Top chamber height: 105mm Maximum clearance above plate: 175mm Note: The rims of the desiccator and lid are ground glass and require greasing before use to create an air-tight seal. (1 per EA)

Desiccators include on three 16mm high feet. Glazed on top surface. (1 per EA)

VDC-21 Vacuum Desiccator, 23L (0.8cu ft), 16.5 x 15.4 x 11.1, 18.1lbs (1 per EA )

Desiccator Plate, PP 141mm (10 per CS)

VDR-20 Vacuum Desiccator, 3.3lbs/ Dia.11.3 x 11.0, 1 Torre, 1.33 x 10^-4 Mpa), 6L (0.2cu ft) (1 per EA )

These autoclavable desiccators are made of polypropylene (PP) and polycarbonate (PC) and can hold a vacuum up to 740mm Hg for 24 hours without any greasing. Autoclavable at 121°C for 15 minutes. The top dome, molded in rigid and transparent PC, gives a crystal-clear view of the sample. The knurled knob on the top provides easy handling of the dome. The lower part is made of PP and includes a perforated PP desiccator plate. An internal groove on the flange holds the silicon rubber O-ring. The PP stopcock accepts 1/4" I.D. tubing and has a self-lubricating PTFE plug. Use the three-way plug to create a vacuum, release a vacuum, or for shut-off. (1 per EA)

These autoclavable desiccators are made of polypropylene (PP) and polycarbonate. Autoclavable at 120°C for 15 minutes. The top dome, molded in rigid and transparent PC, gives a crystal-clear view of the sample. The knurled knob on the top provides easy handling of the dome. The lower part is made of PP. An internal groove on the flange holds the silicon rubber O-ring. Vacuum grease should be applied on the flanges to make it air-tight. (1 per EA)

These autoclavable desiccators are made of polypropylene (PP) and polycarbonate (PC) and can hold a vacuum up to 740mm Hg for 24 hours without any greasing. Autoclavable at 120°C for 15 minutes. The top dome, molded in rigid and transparent PC, gives a crystal-clear view of the sample. The knurled knob on the top provides easy handling of the dome. The transparent PC bottom provides increased viewing clarity. An internal groove on the flange holds the silicon rubber O-ring. The PP stopcock has a self-lubricating PTFE plug. The three-way plug opens to create a vacuum, closes to hold a vacuum, and opens again to release a vacuum. (1 per EA)

Desiccator - Plain, 30cm (1 per EA )

Desiccator Plate, PP 190mm (10 per CS)

Implosion proof desiccators. Will take vacuum of -740 mm Hg with loss (absolute zero: -760 mm/HG) not exceeding 20 mm Hg in 24 hours. (4 per CS)

Desiccator Plate, PP 239mm (10 per CS)

These autoclavable desiccators are made of polypropylene (PP) and polycarbonate. Autoclavable at 120°C for 15 minutes. The top dome, molded in rigid and transparent PC, gives a crystal-clear view of the sample. The knurled knob on the top provides easy handling of the dome. The lower part is made of PP. An internal groove on the flange holds the silicon rubber O-ring. Vacuum grease should be applied on the flanges to make it air-tight. (1 per EA)

Desiccator - Vacuum, 25cm, made of Polypropylene and Polycarbonate (1 per EA )

Plates include 30mm diameter perforations. Also includes large hole in center. Glazed on one side. (1 per EA)

These autoclavable desiccators are made of polypropylene (PP) and polycarbonate (PC) and can hold a vacuum up to 740mm Hg for 24 hours without any greasing. Autoclavable at 120°C for 15 minutes. The top dome, molded in rigid and transparent PC, gives a crystal-clear view of the sample. The knurled knob on the top provides easy handling of the dome. The transparent PC bottom provides increased viewing clarity. An internal groove on the flange holds the silicon rubber O-ring. The PP stopcock has a self-lubricating PTFE plug. The three-way plug opens to create a vacuum, closes to hold a vacuum, and opens again to release a vacuum. (1 per EA)

These autoclavable desiccators are made of polypropylene (PP) and polycarbonate (PC) and can hold a vacuum up to 740mm Hg for 24 hours without any greasing. Autoclavable at 120°C for 15 minutes. The top dome, molded in rigid and transparent PC, gives a crystal-clear view of the sample. The knurled knob on the top provides easy handling of the dome. The transparent PC bottom provides increased viewing clarity. An internal groove on the flange holds the silicon rubber O-ring. The PP stopcock has a self-lubricating PTFE plug. The three-way plug opens to create a vacuum, closes to hold a vacuum, and opens again to release a vacuum. (1 per EA)

Plates include 30mm diameter perforations. Also includes large hole in center. Glazed on one side. (1 per EA)

12" x 12" x 24" high One (1) cubicle Eleven (11) shelf positions Four (4) perforated shelves (1 per EA )